Haven't found what you were looking for ? Mail us !|info@afullmetaljacket.com
  • Savotta Griffin sling HW Savotta Griffin sling HW

    Savotta Griffin sling HW

    €49,90
    An effective, simple and reliable two-point sling, originally designed for a special military customer of ours. The LW (lightweight) Griffin Sling is simple and unobtrusive, made of 25mm/1" webbing without any padding, for submachine guns and light rifles. Check out the MW if you want a little width and padding, or the HW if you need a good thick filling. QUICK ADJUSTMENT SLIDER The heart of the Griffin Sling is our patented slider for quick adjustment. Quick, effortless adjustment allows for an easy transition between carry-shoot-carry etc. under any circumstances. We know the world is full of buckles for adjusting slings, and most of them are pretty good too. We chose to design our own customization hardware for these simple reasons: 1) It must be solid metal with no moving parts 2) It must have the right toothing and protrusions to grip; 3) It must be compatible with the grip lip for use with winter handwear; 4) And it should preferably be made in Finland If you hate the tab of the webbing grip, or just don't need it or whatever, you can cut it off. The serrated sides and the protruding attachment point of the webbing provide good grip. INSTALLATION Since this is a simple two-point sling, you don't have to play with multiple ends of the webbing, only two. The 25mm/1" strap fits most sling swivels and fasteners out there. We make these with long enough woven ends to reach around most people. 1. Open the back loop by passing the woven end through the steel tri-glide buckle. Loop the belt through the sling-swivel, buckle, stock, or whatever attachment point you use on the back of your firearm. Thread the fabric through the buckle again and make a U-turn to lock it in place. 2. Open the front quick adjustment loop and remove the steel tri-glide from the tire. Loop the webbing through your front sling-swivel or buckle, reattach the steel tri-glide and loop the strap around the quick adjustment slider and back through the steel tri-glide. 3. Try to play around with different adjustment lengths on the front and back. Once you've found the right setting, you can roll up the excess webbing ends and stick them in neat bundles. Or, if you dare, cut and burn them. ORIGIN The Griffin Slings are the commercial offspring of a series of slings that we have designed for a military customer according to their requirements. Our customer needed good two-point tires for all types of small arms, including sniper rifles and light machine guns. The slings should carry an unpleasant weight as comfortably as possible, be equipped with a forward pulling force to be able to be extended quickly, fit on different fasteners and must be effective and reliable in "suboptimal conditions" (it is -30 °C, you suffer from sleep deprivation and wearing thick winter gloves and the use of NVGs that ruin your view of everything within arm's length). Then we went on to design the lighter medium version for carbines, and the lightweight one for SMG:s and the like. Because these turned out pretty well, we decided to make them available to the public. So, here you go: the Griffin Slings — fairly fast, low-bullshit slings, named after that mythical half-bird-half-cat creature for some peculiar reason. Main features
    • Two-point sling for sniper rifles and machine guns
    • Thick and sturdy foam cushion of 65 x 10 mm with closed cells
    • All metal hardware (steel and aluminium)
    • Quick loop adjustment slider for grip on webbing
    • Pulling forward lengthens the sling and moves the support hand forward
    • Front quick adjustment loop can be adjusted to the desired length
    • A continuous piece of 25 mm/1" runs through the entire sling
    • The ends of the sling form 25 mm/1" loops for universal attachment
    • 5-year material and manufacturing warranty
    • Gemaakt in Finland
    Technical features
    • Weight: 140 g
    • Length: 185 cm (detached to max. length)
    • Webbing: 100% polyester
    • Fabric: 500D Cordura (100% polyamide)
    • Slider for quick adjustment: aluminum
    • Buckles: steel
    Select options Details
  • Savotta Griffin sling LW Savotta Griffin sling LW

    Savotta Griffin sling LW

    €34,90
    An effective, simple and reliable two-point sling, originally designed for a special military customer of ours. The LW (lightweight) Griffin Sling is simple and unobtrusive, made of 25mm/1" webbing without any padding, for submachine guns and light rifles. Check out the MW if you want a little width and padding, or the HW if you need a good thick filling. QUICK ADJUSTMENT SLIDER The heart of the Griffin Sling is our patented slider for quick adjustment. Quick, effortless adjustment allows for an easy transition between carry-shoot-carry etc. under any circumstances. We know the world is full of buckles for adjusting slings, and most of them are pretty good too. We chose to design our own customization hardware for these simple reasons: 1) It must be solid metal with no moving parts 2) It must have the right toothing and protrusions to grip; 3) It must be compatible with the grip lip for use with winter handwear; 4) And it should preferably be made in Finland If you hate the tab of the webbing grip, or just don't need it or whatever, you can cut it off. The serrated sides and the protruding attachment point of the webbing provide good grip. INSTALLATION Since this is a simple two-point sling, you don't have to play with multiple ends of the webbing, only two. The 25mm/1" strap fits most sling swivels and fasteners out there. We make these with long enough woven ends to reach around most people. 1. Open the back loop by passing the woven end through the steel tri-glide buckle. Loop the belt through the sling-swivel, buckle, stock, or whatever attachment point you use on the back of your firearm. Thread the fabric through the buckle again and make a U-turn to lock it in place. 2. Open the front quick adjustment loop and remove the steel tri-glide from the tire. Loop the webbing through your front sling-swivel or buckle, reattach the steel tri-glide and loop the strap around the quick adjustment slider and back through the steel tri-glide. 3. Try to play around with different adjustment lengths on the front and back. Once you've found the right setting, you can roll up the excess webbing ends and stick them in neat bundles. Or, if you dare, cut and burn them. ORIGIN The Griffin Slings are the commercial offspring of a series of slings that we have designed for a military customer according to their requirements. Our customer needed good two-point tires for all types of small arms, including sniper rifles and light machine guns. The slings should carry an unpleasant weight as comfortably as possible, be equipped with a forward pulling force to be able to be extended quickly, fit on different fasteners and must be effective and reliable in "suboptimal conditions" (it is -30 °C, you suffer from sleep deprivation and wearing thick winter gloves and the use of NVGs that ruin your view of everything within arm's length). Then we went on to design the lighter medium version for carbines, and the lightweight one for SMG:s and the like. Because these turned out pretty well, we decided to make them available to the public. So, here you go: the Griffin Slings — fairly fast, low-bullshit slings, named after that mythical half-bird-half-cat creature for some peculiar reason. Main features
    • Two-point sling for lightweight small arms
    • Full webbing construction, low profile and weight
    • All metal hardware (steel and aluminium)
    • Quick loop adjustment slider for grip on webbing
    • Pulling forward lengthens the sling and moves the support hand forward
    • Front quick adjustment loop can be adjusted to the desired length
    • A continuous piece of 25 mm/1" runs through the entire sling
    • The ends of the sling form 25 mm/1" loops for universal attachment
    • 5-year material and manufacturing warranty
    • Gemaakt in Finland
    Technical features
    • Weight: 80 g
    • Length: 185 cm (detached to max. length)
    • Webbing: 100% polyester
    • Slider for quick adjustment: aluminum
    • Buckles: steel
    Select options Details
  • Savotta Griffin sling MW Savotta Griffin sling MW

    Savotta Griffin sling MW

    €44,90
    An effective, simple and reliable two-point sling, originally designed for a special military customer of ours. The LW (lightweight) Griffin Sling is simple and unobtrusive, made of 25mm/1" webbing without any padding, for submachine guns and light rifles. Check out the MW if you want a little width and padding, or the HW if you need a good thick filling. QUICK ADJUSTMENT SLIDER The heart of the Griffin Sling is our patented slider for quick adjustment. Quick, effortless adjustment allows for an easy transition between carry-shoot-carry etc. under any circumstances. We know the world is full of buckles for adjusting slings, and most of them are pretty good too. We chose to design our own customization hardware for these simple reasons: 1) It must be solid metal with no moving parts 2) It must have the right toothing and protrusions to grip; 3) It must be compatible with the grip lip for use with winter handwear; 4) And it should preferably be made in Finland If you hate the tab of the webbing grip, or just don't need it or whatever, you can cut it off. The serrated sides and the protruding attachment point of the webbing provide good grip. INSTALLATION Since this is a simple two-point sling, you don't have to play with multiple ends of the webbing, only two. The 25mm/1" strap fits most sling swivels and fasteners out there. We make these with long enough woven ends to reach around most people. 1. Open the back loop by passing the woven end through the steel tri-glide buckle. Loop the belt through the sling-swivel, buckle, stock, or whatever attachment point you use on the back of your firearm. Thread the fabric through the buckle again and make a U-turn to lock it in place. 2. Open the front quick adjustment loop and remove the steel tri-glide from the tire. Loop the webbing through your front sling-swivel or buckle, reattach the steel tri-glide and loop the strap around the quick adjustment slider and back through the steel tri-glide. 3. Try to play around with different adjustment lengths on the front and back. Once you've found the right setting, you can roll up the excess webbing ends and stick them in neat bundles. Or, if you dare, cut and burn them. ORIGIN The Griffin Slings are the commercial offspring of a series of slings that we have designed for a military customer according to their requirements. Our customer needed good two-point tires for all types of small arms, including sniper rifles and light machine guns. The slings should carry an unpleasant weight as comfortably as possible, be equipped with a forward pulling force to be able to be extended quickly, fit on different fasteners and must be effective and reliable in "suboptimal conditions" (it is -30 °C, you suffer from sleep deprivation and wearing thick winter gloves and the use of NVGs that ruin your view of everything within arm's length). Then we went on to design the lighter medium version for carbines, and the lightweight one for SMG:s and the like. Because these turned out pretty well, we decided to make them available to the public. So, here you go: the Griffin Slings — fairly fast, low-bullshit slings, named after that mythical half-bird-half-cat creature for some peculiar reason. Main features
    • Two-point sling for assault rifles and similar small arms
    • Thin 35 x 4 mm foam filling with closed cells
    • All metal hardware (steel and aluminium)
    • Quick loop adjustment slider for grip on webbing
    • Pulling forward lengthens the sling and moves the support hand forward
    • Front quick adjustment loop can be adjusted to the desired length
    • A continuous piece of 25 mm/1" runs through the entire sling
    • The ends of the sling form 25 mm/1" loops for universal attachment
    • 5-year material and manufacturing warranty
    • Gemaakt in Finland
    Technical features
    • Weight: 115 grams
    • Length: 185 cm (detached to max. length)
    • Webbing: 100% polyester
    • Fabric: 500D Cordura (100% polyamide)
    • Slider for quick adjustment: aluminum
    • Buckles: steel
    Select options Details
  • Savotta Grumpy Stove Savotta Grumpy Stove

    Savotta Grumpy Stove

    €35,90
    The Grumpy Hobo is the grumpy part of the Savotta Hobo family. If the Happy Stove doesn't meet your requirements for Finnish melancholy, the Grumpy Stove is more likely to do so. Like the Happy Stove, the Grumpy Stove consists of 7 laser-cut stainless steel parts: three side walls, a base, a "grumpy face" and a two-part cooking support. After it clicks into place, the oboe is ready for use. The design of the oboe is aimed at finding a good balance between weight and durability. Despite its lightness, the oboe can carry the weight of a normal coffee pot or saucepan. The oboe comes with a black protective shaft made of 1000D Codura. Once packed into the bag, the Grumpy fits into every dark corner of your backpack - where it belongs to the grumpy fellow guy TECHNICAL SPECIFICATIONS: Material: 0.5 mm laser cut stainless steel. Total dimensions: height 14 cm, width 14 cm, depth 14 cm. Fire chest dimensions: height 9.5 cm (12 cm without lattice), width 10 cm, depth 10 cm. Weight: 250 grams. Material protection axis: 1000D Cordura, PUR-coated. Dimensions of the protective axle and the packed oboe: height 15.5 cm, width 14 cm, depth 1 cm. Weight of the protective bag: 30 g. Warranty: The product has a 1-year warranty for material and manufacturing defects.
    Add to cart Details

  • Savotta Happy Patch

    €9,90
    The Savotta Happy patch - the hook-and-loop fastenable quick solution for loneliness, compatible with all Savotta Jääkäri backpacks. This patch was originally just a thing for Valentine's Day 2020, but due to the high demand, we decided to offer it for sale.
    Select options Details
  • Not in stock - on order
    Savotta Happy Stove Savotta Happy Stove

    Savotta Happy Stove

    €35,90
    The Happy Hobo is the happy part of the Savotta Hobo family. If the Grumpy Stove doesn't fill your sense of Finnish melancholy, this is more likely to be the case with the Happy Stove. Like the Grumpy Stove, the Happy Stove consists of 7 laser-cut stainless steel parts: three side walls, a bottom, a "happy face" and a cooking support in two parts. As soon as it clicks into place, the oboe is ready for use. The design of the oboe is aimed at finding a good balance between weight and durability. Despite its lightness, the oboe can carry the weight of a normal coffee pot or saucepan. The Happy Stove comes with an olive green protective shaft made from 1000D Codura. Once packed in the bag, the Happy fits in every corner of your backpack - where it waits outside for the next happy cooking moment with you? TECHNICAL SPECIFICATIONS: Material: 0.5 mm laser cut stainless steel. Total dimensions: height 14 cm, width 14 cm, depth 14 cm. Fire chest dimensions: height 9.5 cm (12 cm without lattice), width 10 cm, depth 10 cm. Weight: 250 grams. Material protection axis: 1000D Cordura, PUR-coated. Dimensions of the protective axle and the packed oboe: height 15.5 cm, width 14 cm, depth 1 cm. Weight of the protective bag: 30 g. Warranty: The product has a 1-year warranty for material and manufacturing defects.
    Details
  • Savotta Hatka 12L Savotta Hatka 12L

    Savotta Hatka 12L

    €88,95 – €108,95
    At first glance, the Hatka 12L may seem like just a roller bag with shoulder straps, but when you look closer, you'll see that there's actually a lot going on. This design was conceived as part of a special military carrying system, which required a small daypack that could be easily attached to a larger backpack. On the outside are four rows of PALS weaving tapes. These can be used for attaching pouches, bungee cords, and buckles to quickly attach or detach the Hatka to a larger backpack. The four webbing loops at the bottom can be used for elastic cords, so you can carry items under the backpack. Two long internal compartments are there to organize smaller items, and the D-ring provides a point to store small valuables. The large external pocket against your back is large enough for a hydration reservoir or tarp. The simple 25mm webbing shoulder straps are attached to D-rings and completely removable, and therefore also replaceable with padded shoulder straps if you wish. These can also be set as a single diagonal shoulder strap. They are designed to be lightweight, easy to carry and store so you can attach the Hatka to larger packs. KEY FEATURES
    • Capacity approx. 12 litres
    • Quick and secure roll-top closure with SR buckle
    • Simple, detachable 25mm low-profile shoulder straps
    • PALS webbing on the outside
    • Loop for identification and patches on the outside
    • Four loops at the bottom
    • One large external back compartment
    • Two long internal compartments
    • D-ring attachment point on the inside
    • All color options offer good NIR performance
    • 5-year material and product warranty
    • Made in Finland/Estonia/Poland
    TECHNICAL SPECIFICATIONS
    • Weight: 480 g
    • Dimensions: 25 x 40 x 15 cm (W x L x D)
    • Main material: 500D Cordura (100% polyamide)
    • Strap: 100% polyester
    TRICKS AND MODULARITY Clip and tie it to a larger backpack for use as a "grab and go" daypack. You can do this by tucking it under the flap or by using packing straps. The really great way is to attach the Hatka to the side compression or lid straps using G-hooks or PALS mounted SR buckles. You'll need four of them to securely attach the Hatka 12L to the back of your Jääkäri M, L or XL. Please note that these attachment buckles ARE NOT INCLUDED with the backpack. If you need to, you can add a lot of stuff to the outside of this otherwise quite small backpack. The PALS webbing allows you to attach bags, but you can also thread bungee cords to it (along with the four webbing loops at the bottom) for rain gear, tarpaulins etc. Because the Hatka is in many ways a spiritual successor to the venerable 202 daypack, it also has very rudimentary shoulder straps. This reduces weight and bulk, which is great if you're strapping it to a larger backpack. If you need to, you can easily replace it with more advanced padded options. Although there aren't too many compartments, you can still make good use of them if you pack smartly. Of course, you can put your large items in the main compartment, and the two small inner compartments can hold all kinds of small items and even water bottles. The D-ring can be used to clamp or tie small valuables. The external compartment against your back can be used to carry a closed-cell foam pad as a frame cloth, or to carry a tarp or hydration bladder. LEARN FINNISH WITH SAVOTTA "Hatka" is a peculiar Finnish word, it is only used in the phrase "ottaa hatkat" which means "to escape" or "to leave in a hurry". The Hatka pack was conceived while prototyping small, quick-to-remove escape and escape escape kits for a military project, so now you know why this peculiar name makes so much sense.
    Select options Details
  • Not in stock - on order

    Savotta HAWU 4 -Door piece HD-4

    €695,00
    Here in the cold north, we have always relied on heated shelters and tents to keep us alive and head out into the wilderness. The HAWU tents are the latest step in the long evolutionary line of heated Finnish oven tents. What really sets the HAWU apart from its predecessors is the modular structure, which makes it possible to split it up for transport, to lay tree trunks, to expand, to house people, material and much more. Due to its robust construction and functionality, the HAWU has built a solid reputation among both professional and recreational users, including a number of military organizations. MAIN FEATURES:
    • Designed for four people, expandable to six people with an optional centre section
    • Oven compatible for year-round use in any climate thanks to a lockable opening in the oven pipe
    • Durable and fire retardant for continuous use
    • Split in two for transport and use
    • When setting up around a tree trunk, no sticks are required, HAWU tent poles are optionally available
    • Easy to set up by one person
    • 2-year warranty on material and craftsmanship
    • Finnish Key Flag product
    TECHNICAL SPECIFICATIONS: Weight
    • Doorpiece: 4.50 kg
    • Wall piece: 3.50 kg
    • Extension: 3.80 kg
    Dimensions
    • Door + wall parts: 3.50 x 3.50 x 1.60 m (L x W x H)
    • Door + extension + wall parts: 5.00 x 3.50 x 1.60 m (L x W x H)
    Floor space
    • Door + wall parts: 10.00 m2
    • Door + extension + wall parts: 15.25 m2
    • Material: Breathable, rainproof, antifungal and fire retardant special fabric
    HAWU 4 SYSTEM COMPONENTS
    Door piece The front half of the tent with zipper and flue pipe connection can be used as a loose tarpaulin in Loue style Wall piece: The sturdy rear part of the tent can be used as a freestanding Loue-style tarpaulin Expansion: A separate middle section with which the HAWU 4 can be extended to a maximum of six people DETAILED DESCRIPTION
    The HAWU is a highly customizable security system designed for long-term use. It is perfect for the most demanding environments, also for military use all year round. Designed for versatility and adaptability, the HAWU is highly flexible when it comes to finding a suitable place to set up. This requires very few accessories. The core of its flexibility are the zippers that connect the tent parts together and allow them to be distributed and placed around tree trunks.
    The door is designed so that you step into the tent instead of crawling under a low side entrance. A freely hanging inner wall prevents the warm air from escaping from the tent when the zippered door is opened. A useful function if someone has to keep watch at the same time and look at the lit heater.
    There is a steel oven tube opening with a hinged lid between the door and the top of the front part. This design provides safety when using an oven for heating. If no oven is used, the folding cover closes the connection from the outside.
    The side zippers provide a quick way out, especially during military operations or in case of emergency. The zippers and their rolled-up outer cover allow for a very fast emergency exit - open the zipper a little from top to bottom and just push yourself through!
    The top of the tent is made of excess fabric that can be used to cover the top when a center stick is used. The tip can be left completely open or left open only on one side, depending on the wind direction, which regulates the ventilation and evaporation of moisture, depending on the conditions. When using an oven, it is advisable to keep the tip open so that the warm air can drain moisture.
    HAWU tents are standard made of a naturally fire retardant and breathable fabric that has been treated against mold resistance. The fibers in the fabric swell when wet to ensure effective sealing against rain without the need for waterproof and poorly breathable coatings. For large orders, such as procurement by the military and government agencies, we can, and we have done so in the past, make the HAWU from other substances specified by the customer. CONSTRUCTION POSSIBILITIES
    The split design offers flexibility in both transport and assembly. Thanks to the numerous mounting methods, the HAWU can be set up practically anywhere, which minimizes the time and effort required to find the perfect location. Around a tree: The halves can be mounted around a tree trunk, so there is no need to wear or manufacture separate center posts on site. Another advantage of this method is camouflage, where the treetops provide excellent camouflage for aerial exploration. Hanging: Instead of using a central support, trunk or pole, the HAWU can be hung on a rope between two trees. This creates space in the tent for more people or to set up equipment for maintenance and work. With a central pole: the usual old-fashioned way also works with the HAWU. For this we offer specially made telescopic mid-sticks. Side parts: The two halves of the HAWU can be used separately as smaller open protective sails. This allows a larger team to split up and take half the tent with them.
    Due to the smart design of the corner sheath lines, no corner poles are needed. Just cut the lines or tie them around a rock or tree and pull on the quick belt adjusters to adjust the tension, and you're done. The lack of corner bars also means that there are far fewer separate components to maintain and move, which is a big advantage in suboptimal environments and under stress. As such, herrings are not strictly necessary, but are recommended. Although the shaving lines can be attached to the terrain and vegetation, this is not always possible. The corners of the hem should also be attached to the floor for a safe seal. The HAWU tent does not contain pegs, but we offer these as a separate accessory.
    The upper loops and the carabiner mounting system that secures the top of the tent make it possible to set up the HAWU with a standard center pole to attach a tree or hang it at the top. THE HAWU STORY The origins of Hawu tents go back to 1993 when Pasi Ylirisku, the current CEO of Hawu Pro Oy, and his staff began developing a new tent design. For more than two decades, they have tested and improved the Hawu tent to perfection with great attention to detail. In 2016, Finn-Savotta Oy and Hawu Pro Oy signed a cooperation agreement. The design of the Hawu tent was completed in collaboration with Savotta's designers and Hawu's original mass production design and development team. The first batch, which was completed in autumn 2017 and put up for sale.
    Details
  • Not in stock - on order

    Savotta HAWU 4 -Extension piece HE-4

    €595,00
    Here in the cold north, we have always relied on heated shelters and tents to keep us alive and head out into the wilderness. The HAWU tents are the latest step in the long evolutionary line of heated Finnish oven tents. What really sets the HAWU apart from its predecessors is the modular structure, which makes it possible to split it up for transport, to lay tree trunks, to expand, to house people, material and much more. Due to its robust construction and functionality, the HAWU has built a solid reputation among both professional and recreational users, including a number of military organizations. MAIN FEATURES:
    • Designed for four people, expandable to six people with an optional centre section
    • Oven compatible for year-round use in any climate thanks to a lockable opening in the oven pipe
    • Durable and fire retardant for continuous use
    • Split in two for transport and use
    • When setting up around a tree trunk, no sticks are required, HAWU tent poles are optionally available
    • Easy to set up by one person
    • 2-year warranty on material and craftsmanship
    • Finnish Key Flag product
    TECHNICAL SPECIFICATIONS: Weight
    • Doorpiece: 4.50 kg
    • Wall piece: 3.50 kg
    • Extension: 3.80 kg
    Dimensions
    • Door + wall parts: 3.50 x 3.50 x 1.60 m (L x W x H)
    • Door + extension + wall parts: 5.00 x 3.50 x 1.60 m (L x W x H)
    Floor space
    • Door + wall parts: 10.00 m2
    • Door + extension + wall parts: 15.25 m2
    • Material: Breathable, rainproof, antifungal and fire retardant special fabric
    HAWU 4 SYSTEM COMPONENTS
    Door piece The front half of the tent with zipper and flue pipe connection can be used as a loose tarpaulin in Loue style Wall piece: The sturdy rear part of the tent can be used as a freestanding Loue-style tarpaulin Expansion: A separate middle section with which the HAWU 4 can be extended to a maximum of six people DETAILED DESCRIPTION
    The HAWU is a highly customizable security system designed for long-term use. It is perfect for the most demanding environments, also for military use all year round. Designed for versatility and adaptability, the HAWU is highly flexible when it comes to finding a suitable place to set up. This requires very few accessories. The core of its flexibility are the zippers that connect the tent parts together and allow them to be distributed and placed around tree trunks.
    The door is designed so that you step into the tent instead of crawling under a low side entrance. A freely hanging inner wall prevents the warm air from escaping from the tent when the zippered door is opened. A useful function if someone has to keep watch at the same time and look at the lit heater.
    There is a steel oven tube opening with a hinged lid between the door and the top of the front part. This design provides safety when using an oven for heating. If no oven is used, the folding cover closes the connection from the outside.
    The side zippers provide a quick way out, especially during military operations or in case of emergency. The zippers and their rolled-up outer cover allow for a very fast emergency exit - open the zipper a little from top to bottom and just push yourself through!
    The top of the tent is made of excess fabric that can be used to cover the top when a center stick is used. The tip can be left completely open or left open only on one side, depending on the wind direction, which regulates the ventilation and evaporation of moisture, depending on the conditions. When using an oven, it is advisable to keep the tip open so that the warm air can drain moisture.
    HAWU tents are standard made of a naturally fire retardant and breathable fabric that has been treated against mold resistance. The fibers in the fabric swell when wet to ensure effective sealing against rain without the need for waterproof and poorly breathable coatings. For large orders, such as procurement by the military and government agencies, we can, and we have done so in the past, make the HAWU from other substances specified by the customer. CONSTRUCTION POSSIBILITIES
    The split design offers flexibility in both transport and assembly. Thanks to the numerous mounting methods, the HAWU can be set up practically anywhere, which minimizes the time and effort required to find the perfect location. Around a tree: The halves can be mounted around a tree trunk, so there is no need to wear or manufacture separate center posts on site. Another advantage of this method is camouflage, where the treetops provide excellent camouflage for aerial exploration. Hanging: Instead of using a central support, trunk or pole, the HAWU can be hung on a rope between two trees. This creates space in the tent for more people or to set up equipment for maintenance and work. With a central pole: the usual old-fashioned way also works with the HAWU. For this we offer specially made telescopic mid-sticks. Side parts: The two halves of the HAWU can be used separately as smaller open protective sails. This allows a larger team to split up and take half the tent with them.
    Due to the smart design of the corner sheath lines, no corner poles are needed. Just cut the lines or tie them around a rock or tree and pull on the quick belt adjusters to adjust the tension, and you're done. The lack of corner bars also means that there are far fewer separate components to maintain and move, which is a big advantage in suboptimal environments and under stress. As such, herrings are not strictly necessary, but are recommended. Although the shaving lines can be attached to the terrain and vegetation, this is not always possible. The corners of the hem should also be attached to the floor for a safe seal. The HAWU tent does not contain pegs, but we offer these as a separate accessory.
    The upper loops and the carabiner mounting system that secures the top of the tent make it possible to set up the HAWU with a standard center pole to attach a tree or hang it at the top. THE HAWU STORY The origins of Hawu tents go back to 1993 when Pasi Ylirisku, the current CEO of Hawu Pro Oy, and his staff began developing a new tent design. For more than two decades, they have tested and improved the Hawu tent to perfection with great attention to detail. In 2016, Finn-Savotta Oy and Hawu Pro Oy signed a cooperation agreement. The design of the Hawu tent was completed in collaboration with Savotta's designers and Hawu's original mass production design and development team. The first batch, which was completed in autumn 2017 and put up for sale.
    Details
  • Not in stock - on order

    Savotta HAWU 4 -Wall piece HW-4

    €595,00
    Here in the cold north, we have always relied on heated shelters and tents to keep us alive and head out into the wilderness. The HAWU tents are the latest step in the long evolutionary line of heated Finnish oven tents. What really sets the HAWU apart from its predecessors is the modular structure, which makes it possible to split it up for transport, to lay tree trunks, to expand, to house people, material and much more. Due to its robust construction and functionality, the HAWU has built a solid reputation among both professional and recreational users, including a number of military organizations. MAIN FEATURES:
    • Designed for four people, expandable to six people with an optional centre section
    • Oven compatible for year-round use in any climate thanks to a lockable opening in the oven pipe
    • Durable and fire retardant for continuous use
    • Split in two for transport and use
    • When setting up around a tree trunk, no sticks are required, HAWU tent poles are optionally available
    • Easy to set up by one person
    • 2-year warranty on material and craftsmanship
    • Finnish Key Flag product
    TECHNICAL SPECIFICATIONS: Weight
    • Doorpiece: 4.50 kg
    • Wall piece: 3.50 kg
    • Extension: 3.80 kg
    Dimensions
    • Door + wall parts: 3.50 x 3.50 x 1.60 m (L x W x H)
    • Door + extension + wall parts: 5.00 x 3.50 x 1.60 m (L x W x H)
    Floor space
    • Door + wall parts: 10.00 m2
    • Door + extension + wall parts: 15.25 m2
    • Material: Breathable, rainproof, antifungal and fire retardant special fabric
    HAWU 4 SYSTEM COMPONENTS
    Door piece The front half of the tent with zipper and flue pipe connection can be used as a loose tarpaulin in Loue style Wall piece: The sturdy rear part of the tent can be used as a freestanding Loue-style tarpaulin Expansion: A separate middle section with which the HAWU 4 can be extended to a maximum of six people DETAILED DESCRIPTION
    The HAWU is a highly customizable security system designed for long-term use. It is perfect for the most demanding environments, also for military use all year round. Designed for versatility and adaptability, the HAWU is highly flexible when it comes to finding a suitable place to set up. This requires very few accessories. The core of its flexibility are the zippers that connect the tent parts together and allow them to be distributed and placed around tree trunks.
    The door is designed so that you step into the tent instead of crawling under a low side entrance. A freely hanging inner wall prevents the warm air from escaping from the tent when the zippered door is opened. A useful function if someone has to keep watch at the same time and look at the lit heater.
    There is a steel oven tube opening with a hinged lid between the door and the top of the front part. This design provides safety when using an oven for heating. If no oven is used, the folding cover closes the connection from the outside.
    The side zippers provide a quick way out, especially during military operations or in case of emergency. The zippers and their rolled-up outer cover allow for a very fast emergency exit - open the zipper a little from top to bottom and just push yourself through!
    The top of the tent is made of excess fabric that can be used to cover the top when a center stick is used. The tip can be left completely open or left open only on one side, depending on the wind direction, which regulates the ventilation and evaporation of moisture, depending on the conditions. When using an oven, it is advisable to keep the tip open so that the warm air can drain moisture.
    HAWU tents are standard made of a naturally fire retardant and breathable fabric that has been treated against mold resistance. The fibers in the fabric swell when wet to ensure effective sealing against rain without the need for waterproof and poorly breathable coatings. For large orders, such as procurement by the military and government agencies, we can, and we have done so in the past, make the HAWU from other substances specified by the customer. CONSTRUCTION POSSIBILITIES
    The split design offers flexibility in both transport and assembly. Thanks to the numerous mounting methods, the HAWU can be set up practically anywhere, which minimizes the time and effort required to find the perfect location. Around a tree: The halves can be mounted around a tree trunk, so there is no need to wear or manufacture separate center posts on site. Another advantage of this method is camouflage, where the treetops provide excellent camouflage for aerial exploration. Hanging: Instead of using a central support, trunk or pole, the HAWU can be hung on a rope between two trees. This creates space in the tent for more people or to set up equipment for maintenance and work. With a central pole: the usual old-fashioned way also works with the HAWU. For this we offer specially made telescopic mid-sticks. Side parts: The two halves of the HAWU can be used separately as smaller open protective sails. This allows a larger team to split up and take half the tent with them.
    Due to the smart design of the corner sheath lines, no corner poles are needed. Just cut the lines or tie them around a rock or tree and pull on the quick belt adjusters to adjust the tension, and you're done. The lack of corner bars also means that there are far fewer separate components to maintain and move, which is a big advantage in suboptimal environments and under stress. As such, herrings are not strictly necessary, but are recommended. Although the shaving lines can be attached to the terrain and vegetation, this is not always possible. The corners of the hem should also be attached to the floor for a safe seal. The HAWU tent does not contain pegs, but we offer these as a separate accessory.
    The upper loops and the carabiner mounting system that secures the top of the tent make it possible to set up the HAWU with a standard center pole to attach a tree or hang it at the top. THE HAWU STORY The origins of Hawu tents go back to 1993 when Pasi Ylirisku, the current CEO of Hawu Pro Oy, and his staff began developing a new tent design. For more than two decades, they have tested and improved the Hawu tent to perfection with great attention to detail. In 2016, Finn-Savotta Oy and Hawu Pro Oy signed a cooperation agreement. The design of the Hawu tent was completed in collaboration with Savotta's designers and Hawu's original mass production design and development team. The first batch, which was completed in autumn 2017 and put up for sale.
    Details
  • Not in stock - on order
    Savotta HAWU 8 -By piece HD-8

    Savotta HAWU 8 -By piece HD-8

    €895,00
    Here in the cold north, we have always relied on heated shelters and tents to keep us alive and head out into the wilderness. The HAWU tents are the latest step in the long evolutionary line of heated Finnish oven tents. What really sets the HAWU apart from its predecessors is the modular structure, which makes it possible to split it up for transport, to lay tree trunks, to expand, to house people, material and much more. Due to its robust construction and functionality, the HAWU has built a solid reputation among both professional and recreational users, including a number of military organizations. MAIN FEATURES:
    • Designed for 8 people, expandable to 12 people with an optional center area
    • Oven compatible for year-round use in any climate thanks to a lockable opening in the oven pipe
    • Durable and fire retardant for continuous use
    • Split in two for transport and use
    • When setting up around a tree trunk, no sticks are required, HAWU tent poles are optionally available
    • Easy to set up by one person
    • 2-year warranty on material and craftsmanship
    TECHNICAL SPECIFICATIONS: Weight
    • Door piece: 6 kg
    • Wall piece: 5 kg
    • Extension: 4.50 kg
    Dimensions
    • Door + wall parts: 4 x 4 x 1.70 m (L x W x H)
    • Door + extension + wall parts: 5.50 x 4 x 1.70 m (L x W x H)
    Floor space
    • Door + wall parts: 13.00 m2
    • Door + extension + wall parts: 19 m2
    • Material: Breathable, rainproof, antifungal and fire retardant special fabric
    HAWU 4 SYSTEM COMPONENTS
    HAWU 8
    HAWU 8
    Door piece
    • Door piece: The front half of the tent with zipper and flue pipe connection can be used as a freestanding tarpaulin in Loue style
    • Wall piece: The sturdy rear part of the tent can be used as a freestanding Loue-style tarpaulin
    • Expansion: A separate middle section with which the HAWU 8 can be extended to twelve people
    DETAILED DESCRIPTION
    HAWU 8
    The HAWU is a highly customizable security system designed for long-term use. It is perfect for the most demanding environments, also for military use all year round. Designed for versatility and adaptability, the HAWU is highly flexible when it comes to finding a suitable place to set up. This requires very few accessories. The core of its flexibility are the zippers that connect the tent parts together and allow them to be distributed and placed around tree trunks.
    The door is designed so that you step into the tent instead of crawling under a low side entrance. A freely hanging inner wall prevents the warm air from escaping from the tent when the zippered door is opened. A useful function if someone has to keep watch at the same time and look at the lit heater.
    There is a steel oven tube opening with a hinged lid between the door and the top of the front part. This design provides safety when using an oven for heating. If no oven is used, the folding cover closes the connection from the outside.
    HAWU 8
    The side zippers provide a quick way out, especially during military operations or in case of emergency. The zippers and their rolled-up outer cover allow for a very fast emergency exit - open the zipper a little from top to bottom and just push yourself through!
    The top of the tent is made of excess fabric that can be used to cover the top when a center stick is used. The tip can be left completely open or left open only on one side, depending on the wind direction, which regulates the ventilation and evaporation of moisture, depending on the conditions. When using an oven, it is advisable to keep the tip open so that the warm air can drain moisture.
    HAWU tents are standard made of a naturally fire retardant and breathable fabric that has been treated against mold resistance. The fibers in the fabric swell when wet to ensure effective sealing against rain without the need for waterproof and poorly breathable coatings. For large orders, such as procurement by the military and government agencies, we can, and we have done so in the past, make the HAWU from other substances specified by the customer. CONSTRUCTION POSSIBILITIES
    The split design offers flexibility in both transport and assembly. Thanks to the numerous mounting methods, the HAWU can be set up practically anywhere, which minimizes the time and effort required to find the perfect location. Around a tree: The halves can be mounted around a tree trunk, so there is no need to wear or manufacture separate center posts on site. Another advantage of this method is camouflage, where the treetops provide excellent camouflage for aerial exploration. Hanging: Instead of using a central support, trunk or pole, the HAWU can be hung on a rope between two trees. This creates space in the tent for more people or to set up equipment for maintenance and work. With a central pole: the usual old-fashioned way also works with the HAWU. For this we offer specially made telescopic mid-sticks. Side parts: The two halves of the HAWU can be used separately as smaller open protective sails. This allows a larger team to split up and take half the tent with them.
    Due to the smart design of the corner sheath lines, no corner poles are needed. Just cut the lines or tie them around a rock or tree and pull on the quick belt adjusters to adjust the tension, and you're done. The lack of corner bars also means that there are far fewer separate components to maintain and move, which is a big advantage in suboptimal environments and under stress. As such, herrings are not strictly necessary, but are recommended. Although the shaving lines can be attached to the terrain and vegetation, this is not always possible. The corners of the hem should also be attached to the floor for a safe seal. The HAWU tent does not contain pegs, but we offer these as a separate accessory.
    The upper loops and the carabiner mounting system that secures the top of the tent make it possible to set up the HAWU with a standard center pole to attach a tree or hang it at the top. THE HAWU STORY The origins of Hawu tents go back to 1993 when Pasi Ylirisku, the current CEO of Hawu Pro Oy, and his staff began developing a new tent design. For more than two decades, they have tested and improved the Hawu tent to perfection with great attention to detail. In 2016, Finn-Savotta Oy and Hawu Pro Oy signed a cooperation agreement. The design of the Hawu tent was completed in collaboration with Savotta's designers and Hawu's original mass production design and development team. The first batch, which was completed in autumn 2017 and put up for sale.
    Details
  • Not in stock - on order
    Savotta HAWU 8 -By piece HD-8 Savotta HAWU 8 -By piece HD-8

    Savotta HAWU 8 -Extension piece HE-8

    €795,00
    Here in the cold north, we have always relied on heated shelters and tents to keep us alive and head out into the wilderness. The HAWU tents are the latest step in the long evolutionary line of heated Finnish oven tents. What really sets the HAWU apart from its predecessors is the modular structure, which makes it possible to split it up for transport, to lay tree trunks, to expand, to house people, material and much more. Due to its robust construction and functionality, the HAWU has built a solid reputation among both professional and recreational users, including a number of military organizations. MAIN FEATURES:
    • Designed for 8 people, expandable to 12 people with an optional center area
    • Oven compatible for year-round use in any climate thanks to a lockable opening in the oven pipe
    • Durable and fire retardant for continuous use
    • Split in two for transport and use
    • When setting up around a tree trunk, no sticks are required, HAWU tent poles are optionally available
    • Easy to set up by one person
    • 2-year warranty on material and craftsmanship
    TECHNICAL SPECIFICATIONS: Weight
    • Door piece: 6 kg
    • Wall piece: 5 kg
    • Extension: 4.50 kg
    Dimensions
    • Door + wall parts: 4 x 4 x 1.70 m (L x W x H)
    • Door + extension + wall parts: 5.50 x 4 x 1.70 m (L x W x H)
    Floor space
    • Door + wall parts: 13.00 m2
    • Door + extension + wall parts: 19 m2
    • Material: Breathable, rainproof, antifungal and fire retardant special fabric
    HAWU 4 SYSTEM COMPONENTS
    HAWU 8
    HAWU 8
    Door piece
    • Door piece: The front half of the tent with zipper and flue pipe connection can be used as a freestanding tarpaulin in Loue style
    • Wall piece: The sturdy rear part of the tent can be used as a freestanding Loue-style tarpaulin
    • Expansion: A separate middle section with which the HAWU 8 can be extended to twelve people
    DETAILED DESCRIPTION
    HAWU 8
    The HAWU is a highly customizable security system designed for long-term use. It is perfect for the most demanding environments, also for military use all year round. Designed for versatility and adaptability, the HAWU is highly flexible when it comes to finding a suitable place to set up. This requires very few accessories. The core of its flexibility are the zippers that connect the tent parts together and allow them to be distributed and placed around tree trunks.
    The door is designed so that you step into the tent instead of crawling under a low side entrance. A freely hanging inner wall prevents the warm air from escaping from the tent when the zippered door is opened. A useful function if someone has to keep watch at the same time and look at the lit heater.
    There is a steel oven tube opening with a hinged lid between the door and the top of the front part. This design provides safety when using an oven for heating. If no oven is used, the folding cover closes the connection from the outside.
    HAWU 8
    The side zippers provide a quick way out, especially during military operations or in case of emergency. The zippers and their rolled-up outer cover allow for a very fast emergency exit - open the zipper a little from top to bottom and just push yourself through!
    The top of the tent is made of excess fabric that can be used to cover the top when a center stick is used. The tip can be left completely open or left open only on one side, depending on the wind direction, which regulates the ventilation and evaporation of moisture, depending on the conditions. When using an oven, it is advisable to keep the tip open so that the warm air can drain moisture.
    HAWU tents are standard made of a naturally fire retardant and breathable fabric that has been treated against mold resistance. The fibers in the fabric swell when wet to ensure effective sealing against rain without the need for waterproof and poorly breathable coatings. For large orders, such as procurement by the military and government agencies, we can, and we have done so in the past, make the HAWU from other substances specified by the customer. CONSTRUCTION POSSIBILITIES
    The split design offers flexibility in both transport and assembly. Thanks to the numerous mounting methods, the HAWU can be set up practically anywhere, which minimizes the time and effort required to find the perfect location. Around a tree: The halves can be mounted around a tree trunk, so there is no need to wear or manufacture separate center posts on site. Another advantage of this method is camouflage, where the treetops provide excellent camouflage for aerial exploration. Hanging: Instead of using a central support, trunk or pole, the HAWU can be hung on a rope between two trees. This creates space in the tent for more people or to set up equipment for maintenance and work. With a central pole: the usual old-fashioned way also works with the HAWU. For this we offer specially made telescopic mid-sticks. Side parts: The two halves of the HAWU can be used separately as smaller open protective sails. This allows a larger team to split up and take half the tent with them.
    Due to the smart design of the corner sheath lines, no corner poles are needed. Just cut the lines or tie them around a rock or tree and pull on the quick belt adjusters to adjust the tension, and you're done. The lack of corner bars also means that there are far fewer separate components to maintain and move, which is a big advantage in suboptimal environments and under stress. As such, herrings are not strictly necessary, but are recommended. Although the shaving lines can be attached to the terrain and vegetation, this is not always possible. The corners of the hem should also be attached to the floor for a safe seal. The HAWU tent does not contain pegs, but we offer these as a separate accessory.
    The upper loops and the carabiner mounting system that secures the top of the tent make it possible to set up the HAWU with a standard center pole to attach a tree or hang it at the top. THE HAWU STORY The origins of Hawu tents go back to 1993 when Pasi Ylirisku, the current CEO of Hawu Pro Oy, and his staff began developing a new tent design. For more than two decades, they have tested and improved the Hawu tent to perfection with great attention to detail. In 2016, Finn-Savotta Oy and Hawu Pro Oy signed a cooperation agreement. The design of the Hawu tent was completed in collaboration with Savotta's designers and Hawu's original mass production design and development team. The first batch, which was completed in autumn 2017 and put up for sale.
    Details
  • Not in stock - on order
    Savotta HAWU 8 -By piece HD-8

    Savotta HAWU 8 -Wall piece HW-8

    €795,00
    Here in the cold north, we have always relied on heated shelters and tents to keep us alive and head out into the wilderness. The HAWU tents are the latest step in the long evolutionary line of heated Finnish oven tents. What really sets the HAWU apart from its predecessors is the modular structure, which makes it possible to split it up for transport, to lay tree trunks, to expand, to house people, material and much more. Due to its robust construction and functionality, the HAWU has built a solid reputation among both professional and recreational users, including a number of military organizations. MAIN FEATURES:
    • Designed for 8 people, expandable to 12 people with an optional center area
    • Oven compatible for year-round use in any climate thanks to a lockable opening in the oven pipe
    • Durable and fire retardant for continuous use
    • Split in two for transport and use
    • When setting up around a tree trunk, no sticks are required, HAWU tent poles are optionally available
    • Easy to set up by one person
    • 2-year warranty on material and craftsmanship
    TECHNICAL SPECIFICATIONS: Weight
    • Door piece: 6 kg
    • Wall piece: 5 kg
    • Extension: 4.50 kg
    Dimensions
    • Door + wall parts: 4 x 4 x 1.70 m (L x W x H)
    • Door + extension + wall parts: 5.50 x 4 x 1.70 m (L x W x H)
    Floor space
    • Door + wall parts: 13.00 m2
    • Door + extension + wall parts: 19 m2
    • Material: Breathable, rainproof, antifungal and fire retardant special fabric
    HAWU 4 SYSTEM COMPONENTS
    HAWU 8
    HAWU 8
    Door piece
    • Door piece: The front half of the tent with zipper and flue pipe connection can be used as a freestanding tarpaulin in Loue style
    • Wall piece: The sturdy rear part of the tent can be used as a freestanding Loue-style tarpaulin
    • Expansion: A separate middle section with which the HAWU 8 can be extended to twelve people
    DETAILED DESCRIPTION
    HAWU 8
    The HAWU is a highly customizable security system designed for long-term use. It is perfect for the most demanding environments, also for military use all year round. Designed for versatility and adaptability, the HAWU is highly flexible when it comes to finding a suitable place to set up. This requires very few accessories. The core of its flexibility are the zippers that connect the tent parts together and allow them to be distributed and placed around tree trunks.
    The door is designed so that you step into the tent instead of crawling under a low side entrance. A freely hanging inner wall prevents the warm air from escaping from the tent when the zippered door is opened. A useful function if someone has to keep watch at the same time and look at the lit heater.
    There is a steel oven tube opening with a hinged lid between the door and the top of the front part. This design provides safety when using an oven for heating. If no oven is used, the folding cover closes the connection from the outside.
    HAWU 8
    The side zippers provide a quick way out, especially during military operations or in case of emergency. The zippers and their rolled-up outer cover allow for a very fast emergency exit - open the zipper a little from top to bottom and just push yourself through!
    The top of the tent is made of excess fabric that can be used to cover the top when a center stick is used. The tip can be left completely open or left open only on one side, depending on the wind direction, which regulates the ventilation and evaporation of moisture, depending on the conditions. When using an oven, it is advisable to keep the tip open so that the warm air can drain moisture.
    HAWU tents are standard made of a naturally fire retardant and breathable fabric that has been treated against mold resistance. The fibers in the fabric swell when wet to ensure effective sealing against rain without the need for waterproof and poorly breathable coatings. For large orders, such as procurement by the military and government agencies, we can, and we have done so in the past, make the HAWU from other substances specified by the customer. CONSTRUCTION POSSIBILITIES
    The split design offers flexibility in both transport and assembly. Thanks to the numerous mounting methods, the HAWU can be set up practically anywhere, which minimizes the time and effort required to find the perfect location. Around a tree: The halves can be mounted around a tree trunk, so there is no need to wear or manufacture separate center posts on site. Another advantage of this method is camouflage, where the treetops provide excellent camouflage for aerial exploration. Hanging: Instead of using a central support, trunk or pole, the HAWU can be hung on a rope between two trees. This creates space in the tent for more people or to set up equipment for maintenance and work. With a central pole: the usual old-fashioned way also works with the HAWU. For this we offer specially made telescopic mid-sticks. Side parts: The two halves of the HAWU can be used separately as smaller open protective sails. This allows a larger team to split up and take half the tent with them.
    Due to the smart design of the corner sheath lines, no corner poles are needed. Just cut the lines or tie them around a rock or tree and pull on the quick belt adjusters to adjust the tension, and you're done. The lack of corner bars also means that there are far fewer separate components to maintain and move, which is a big advantage in suboptimal environments and under stress. As such, herrings are not strictly necessary, but are recommended. Although the shaving lines can be attached to the terrain and vegetation, this is not always possible. The corners of the hem should also be attached to the floor for a safe seal. The HAWU tent does not contain pegs, but we offer these as a separate accessory.
    The upper loops and the carabiner mounting system that secures the top of the tent make it possible to set up the HAWU with a standard center pole to attach a tree or hang it at the top. THE HAWU STORY The origins of Hawu tents go back to 1993 when Pasi Ylirisku, the current CEO of Hawu Pro Oy, and his staff began developing a new tent design. For more than two decades, they have tested and improved the Hawu tent to perfection with great attention to detail. In 2016, Finn-Savotta Oy and Hawu Pro Oy signed a cooperation agreement. The design of the Hawu tent was completed in collaboration with Savotta's designers and Hawu's original mass production design and development team. The first batch, which was completed in autumn 2017 and put up for sale.
    Details
  • Savotta Helmet Camo Scrim Savotta Helmet Camo Scrim

    Savotta Helmet Camo Scrim

    €19,90 – €22,90
    While natural foliage is the ultimate helmet camouflage, a bushy cover with a 3D effect might be the next best thing. Quick and easy to use, easy to customize. They effectively break up helmet silhouettes and provide quick camouflage adjustment to suit different environments. The design is very simple, a single flat piece of 500D Cordura with alternating zigzag shapes cut into it. The zigzag pattern is positioned in such a way that it creates an opening for NVG mounts on the front. Small slits have been cut around the edges for the elastic cord. Thread the elastic cord through the slits, tie it at the back, and pull it over your helmet like a shower cap. Finish it off by pulling back any excess material and rolling it underneath yourself to tighten the cover. If you want to adjust the fit, you can play around with threading the elastic cord through the slits and zigzag pattern in different ways. And if you get really wild and feel the need: you can even cut off excess material from the cover, but of course, such huge adjustments are at your own risk. KEY FEATURES
    • 3D Effect Camouflage Plate for Helmets
    • One-size-fits-most, best suited for high-cut L and XL helmets
    • Lightweight Laser Cut 500D Cordura
    • Quick and easy to apply and remove
    • All color options offer good NIR performance
    • 2-year material and product warranty
    • Gemaakt in Finland
    TECHNICAL SPECIFICATIONS
    • Weight (in retail container): 65 g
    • Dimensions (in retail packaging): 10 x 15 x 4 cm (W x L x D)
    • Fabric: 500D Cordura (100% polyamide)
    Select options Details
  • Savotta High Cut Helmet Cover V1 Savotta High Cut Helmet Cover V1

    Savotta High Cut Helmet Cover V1

    €69,90
    A versatile helmet cover with the right camouflage attachment cords throughout. Designed around the geometry of the Ops Core FAST XP high cut helmet shell, but also fits many other high cut helmets. The world is full of covers for high-cut helmets, but since 99% of these covers don't offer a real way to properly camouflage the helmet with foliage etc., we decided to unleash our offer on those as well. Made of 500D Cordura instead of regular garment fabric for high abrasion resistance. Unlike most high-cut helmet covers, which only have that zigzag cord at the top, our cover has elastic cord attachment points around the helmet shell. This allows you to camouflage your helmet well with foliage and the like. Because the elastic cord is not sewn to the cover, you can choose not to use it at all or to adjust or replace it as needed. The back of the case features a piece of 25mm webbing, with bartacked mounting points for IR strobes and the like. Then we have the standard loops on the sides, top and back for identifiers, patches, cameras, pockets for counterweight etc. The cover is attached via six pieces of one-wrap to pieces of hook on the inside of the helmet shell. If your specific helmet doesn't have pieces of hook exactly where it needs to: that's why we supply a piece of self-adhesive hook of 50 x 150 mm with every cover! Cut and paste it wherever you need it. KEY FEATURES
    • Designed for Ops-Core FAST XP scale geometry
    • Also fits many other high-cut helmets
    • Abrasion resistant 500D Cordura
    • Elastic cord for foliage and all-round cable routing
    • 25mm webbing on the back for IR flashes etc.
    • 50mm loop on the sides and top
    • 100 x 100 mm loop on the back
    • One-Wrap attachment in the helmet shell
    • Comes with a 50 x 100 mm piece of self-adhesive hook
    • All color options offer good NIR performance
    • 5-year material and manufacturer's warranty
    • Gemaakt in Finland
    TECHNICAL SPECIFICATIONS
    • Weight: L: 100 g, XL: 105 g
    • Fabric: 500D Cordura (100% polyamide)
    • Strap: 100% polyester
    SIZE, FIT AND COMPATIBILITY The sizes are matched to the Ops-Core FAST helmet sizes. A cover in size L fits a helmet in size L, a cover in size XL fits on a helmet shell in size XL. At the moment we don't offer M or XXL size covers, but L size covers fit M size shells (and XL size covers also fit L size shells) with the elastic cord as a kind of size adjustment system. Don't forget that each cover comes with a piece of adhesive hook tape, use this to create suitable attachment points in your helmet for the attachment straps! With the elastic cord that surrounds the helmet, you can tighten and shape the case to better fit the contours of helmet shells of different shapes and sizes. In addition to the perfect match, the Ops-Core FAST XP, we also tested the fit on a number of other common helmet designs:
    • Ops-Core FAST SF (super high cut): fits pretty nicely after some tweaking
    • UaRms TOR-D (slightly thicker helmet shell than Ops-Core): fits very well
    • Galvion Caiman ballistic (very different shape): fits quite well after some adjustments
    • PGD ARCH (old generation, Ops-Core XP shell geometry): fits very nicely
    • PGD ARCH/MICH (current (2023) gen): Fits, but NVD bungees and rear rail screws end up under the cover*.
    *The current-generation PGD ARCH/MICH helmet rails are covered by the visor at the front and rear. This blocks access to the rear rail screws (NVD ballast bag attachment) and the NVD bungee cords at the front of the rails. You can easily customize the cover by carefully cutting small holes (and burning them gently to avoid fraying) for the bungees and screws. Changes to the cover are of course at your own risk!
    Select options Details
  • Not in stock - on order
    Savotta HIISI 2 Savotta HIISI 2

    Savotta HIISI 2

    €368,95
    The Savotta Hiisi 2 is a portable double sauna tent for outdoors, easy to carry and can be set up almost anywhere. The light weight and compact packaging size allow easy transport and storage. Take it to the beach, deep forests, mountains or backyard and enjoy a truly warming Finnish sauna session wherever you are. Stove and benches are sold separately! KEY FEATURES
    • Designed for two people
    • Easy to transport and set up
    • Compatible with the Savotta stove + stone rack
    • Fire retardants
    • Transport bag included
    • Four corner poles and six poles included
    • 2-year warranty on material and manufacture
    • Made in Finland &Estonia
    TECHNICAL SPECIFICATIONS
    • Weight: 5,6 kg (incl. all accessories)
    • Dimensions: - Width: 170 cm - Length: 150 cm - Side height: 140/160 cm Pack size: 165 x 20 x 10 cm
    • Floor area: 2,55 m²
    • Materials: - Fabric: 210D polyamide, fire retardant and antifungal - Transport bag: 600D polyester - Poles: aluminium - Stakes: galvanized steel
    DETAILED DESCRIPTION The sauna has been a central and respected place in Finnish life for centuries, a place of birth and death, life and celebration. The word "hiisi" is old Finnish for a sacred place, a place of sacrifice or mystical power - the perfect family name for our sauna tents and accessories. The Hiisi 2 is a renewed design based on the old Hikimaja. The tent itself is actually a box with a sloping roof, not a center post. The corner poles are put into tubes on the outside of the tent, so that it is less crowded inside. The ceiling and wall materials are fire retardant for safety, but not fireproof, so sparks and flames will burn holes in them, so be careful. The interior is large enough for a double sofa, two people and the stove. The stove is placed in the far right corner, as seen from the entrance. The sofa is placed against the left wall, under the window. The window along the top edge of the sofa wall provides some light and a chance to look outside. The entrance is a simple zippered slot. A piece of cord is attached to the ceiling seam of the back wall, this is an attachment point for a sauna thermometer to help you monitor the temperature and not overheat the tent. The tent, poles and stakes can be neatly transported in a carrying case. Shoulder straps make it possible to carry a backpack and free up your hands for stoves or other accessories.
    INSTRUCTIONS - READ BEFORE USE! We recommend two to four people to set up the Hiisi 2. You need a hammer or something similar to hit the poles in the ground. We recommend using a sauna thermometer up to 100°C to prevent overheating and help you get the perfect temperature. 1. Find a suitable flat spot approx. 3.5 x 3.5 m, beware of dangers:
    • Dry grass and undergrowth, trees and branches (fire hazard).
    • Uneven surface (stove or users may stumble and fall).
    2. Unpack the tent canvas and insert the corner poles into the covers. 3. Spread the tent cloth with the poles approximately where you want it. 4. Aim one or two opposite corners at once:
    • Hammer a pole into the ground approx. 140/160 cm (wall height) from the corner.
    • Attach the corner guy line with a reliable knot to the pole.
    • Repeat until all the corners are in place and each shaving cord is fastened to the ground.
    5. Inspect the tent, correct if necessary by adjusting the poles, poles and ropes. 6. Install the stove and the sofa. 7. If necessary, attach a sauna thermometer up to 100°C to the line hanging from the ceiling.
    • The thermometer should hang 140 cm above the ground.
    8. Do not heat the interior above 75 ° C, extreme overheating can damage the tent and is unnecessary - it is steam that makes the sauna pleasant, not hot air. 9. Enjoy (with caution)! Warnings: This sauna tent is designed to be heated with the Savotta wood stove and stone rack. With improper use, the heated heater can cause numerous dangers and physical injury:
    • Savotta sauna tents are not designed for long-term stationary use and must be disassembled, cleaned, dried and stored indoors between uses. Sunlight will damage the substances over time. If you leave a tent upright for a few months, it will damage and any damage resulting from this type of abuse is not covered by our warranty.
    • To prevent damage to the tent from falling sparks, the chimney top should protrude 100 cm above the chimney gate. We recommend burning hardwood to minimize the risk of sparks.
    • Although the fabrics are fire retardant and self-extinguishing, they are not refractory - sparks and flames will damage the substance and burn holes in the fabric. Heater-heated tents will suffer from burnt holes due to sparks that touch the fabric during normal use. This is normal wear and tear and can be easily repaired if necessary. Our warranty does not cover fire damage due to normal or incorrect use.
    • Only use stones intended for sauna use. Improper stones, when heated, can crack and cause injuries from flying shrapnel.
    • Sparks and heat from the stove can set fire to combustible material nearby, easily remove combustible material in and near the tent before use.
    • Always keep a large bucket of water or a fire extinguisher within seconds range of the tent when the stove is hot, be prepared to put out any fire!
    • The stove and stones are extremely hot when heated and can cause injuries when touched!
    • After use, inspect the soil for any hot embers and extinguish it with water.
    Details

Title

Go to Top