Weapon maintenance - Page 2 of 4 - A FULL METAL JACKET SHOP

Not in stock - on order
Fluna Tec Anti-Fog optics care set

€39,90
THE FLUNA TEC OPTIC CARE SET For anyone who wants to clean and care optimally for hunting and sports optics. With this set, you get all the products you need for professional cleaning of the optics, including anticondens for all lenses. The set contains the following individual products:

Fluna TFT / optic cleaner 100ml (RETFT00701)

Fluna isopropanol 50ml (RIS0050120)

Fluna Anti Fog 50ml (ABG0050120)

Microfibre cloth 40 / 40cm

Glass polish 20/20 each packed

On the back of the inlet is a detailed product description.

The product description of the individual products in the set can be found in the relevant item.

Instructions:

First, remove loose dust from the optics – preferably by "blowing out" with a jet of compressed air.

Clean the optics with the Fluna TFT/optic foam cleaner. Turn off electrical appliances for cleaning. Apply foam cleaner evenly thin (leave briefly inactive in case of strong pollution). Dry brush with the clean microfibre cloth.

After cleaning, spray the glass of the optics with the isopropanol alcohol, to defropher the surface. Divide the alcohol with the included glass cloth and wipe away the excess liquid. Let the surface dry for a few seconds.

Then spray the product Fluna spray against covering evenly thin on the glass surface and let the flow substance in for about 2 minutes. Then take the glass polish cloth and brush the glass surface evenly for as long until there is no more liquid to be seen and the glass surface is evenly covered and streakless. Allow the coating to dry for at least 30 minutes. To you can breathe against the glass. If the coating is applied correctly, the mist should dissolve immediately.
Details
Ballistol Teflon Spray 400ml

€11,95
The finest Teflon ™ /PTFE particles sprayed on to it:

clean dry lubrication without attaching dirt and greasy hands,

effective reduction of static, sliding and rolling friction.

Ideal for rollers, bearings, slides, guide rails, telescopic conductors and much more. Suitable for all metal and plastic parts!

BALLISTOL Teflon ™ Spray is silicone, acid and resin-free and does not harden. The hygienic dry lubrication/ solid lubrication. Constant and permanent lubrication and sliding without oil or grease. Therefore, no dirt or dust attach to the treated surface. There is also no disturbing lubricant sludge. Hygienic, clean and environmentally friendly. The PTFE particles in the submicron range attach even on supposedly very smooth surfaces and give the material an effective glide activity. Successfully tested and tested for all glide layers and for drastically reducing static and roller friction. Typical applications: To drastically reduce static, sliding and rolling friction in rollers and bearings, slides and guide rails, cable tractors and telescopic conductors, gears and gears. Application: shake well before use. Spray on the parts or smooth to be lubricated or surfaced at a distance of 10-25 cm and allow to dry for several minutes Is your PTFE layer sufficient? The static friction of PTFE is just as large as the sliding friction, so the transition from standstill to movement is shock-free. Teflon ™ is a trademark of The Chemours Company FC, LLC used under license by F.W. Klever GmbH
Add to cart Details
Ballistol Silicone Spray 400ml

€11,95

Silicone oil is great for lubricating metal, rubber, plastic, wood and leather. Silicone has the pleasant feature that it is "dry", and therefore does not drip or drip. Silicone attaches strongly to all surfaces and provide protection for extended periods. Silicone is ideal for lubricating constructions in which a mixture of materials are used, such as metal and rubber and/or plastic. The oil reduces friction and dampens noise. Beeps and creaks disappear like snow in the sun. A layer of oil protects surfaces from -50 C to +200 C and therefore has a wide scope both at home and in the industry. Free of environmentally toxic substances and chlorinated hydrocarbons. Contains biodegradable solvents and ozone neutral propellant. Typical applications: Plastic gears, plastic gears, rubber bearings, cables, guardrails, rubber strips, window seals, conductors, rollers, slides Application: For use, shake properly. Spray on clean surfaces. Spray evenly at a distance of 25 - 30 cm. Wipe away excess product. Repeat the application if necessary.

Add to cart Details
Gamo electric compressor EU plug for PCP air rifle

€624,95

Electric GAMO compressor, portable all-in-one, up to 320 bar to fill the tank of your PCP. With 220V "charger" and car. With Gamo you can easily and comfortably fill your PCP; Economic

Compressor for PCP rifles 250 W

· Maximum 320 bar, 3 loading phases; It's manual.

· Voltage 220v, 220v charger (12V / 220V) or car connection

· Weight: 9 kg

Exhaust air: 11 l / min.

Rising air flow rate: 2700 r.p.m./min

– 0.5 air cylinder. It takes 6 to 7 minutes from 200 to 300 bars

– 0.5 air cylinder. It takes 18 to 20 minutes from 0 bar to 300 bar 110 – 220 V

Only to fill the "tank" of carbine or pistol, no large bottles.

Add to cart Details
Not in stock - on order
Ballistol Startwunder Spray 200ml

€6,45
Thanks to this Motor Starter Aid Spray, a cold start of all internal combustion engines is possible when cold, humidity or rusted spark plugs make the start more difficult. The StartHulp can be used in all seasons. The Starter Aid Spray is ideal for car, motorcycle, moped, boat, tractor, lawnmower, lawnmower, snow ploughs, emergency power generators etc. Starter wonder is very suitable for 2-stroke and 4-stroke engines. Starter miracle can be used in diesel, petrol, gas and shaky engines and in biodiesel.
Start wonder 200ml properties:

A fast start for all engines in all seasons

Offers a fast start with damp and cold engines

Start aid for engines that have been stationary for a long time and with rusted spark plugs

Suitable for car, motorcycle, moped, boat, tractor, lawnmower and emergency power generator

Suitable for 2-stroke and 4-stroke engines

For all internal combustion engines such as diesel, petrol, biodiesel, gas and shaky engine

use:
Stick Starter Aid Spray on the air filter for approx. 2 seconds or spray directly into the intake manifold. With petrol engines, give a little gas during start-up. Diesel engines are started full of gas without pre-annealing.
Details
Not in stock - on order
Ballistol Teflon Spray 200ml

€8,95
The finest Teflon ™ /PTFE particles sprayed on to it:

clean dry lubrication without attaching dirt and greasy hands,

effective reduction of static, sliding and rolling friction.

Ideal for rollers, bearings, slides, guide rails, telescopic conductors and much more. Suitable for all metal and plastic parts!

BALLISTOL Teflon ™ Spray is silicone, acid and resin-free and does not harden. The hygienic dry lubrication/ solid lubrication. Constant and permanent lubrication and sliding without oil or grease. Therefore, no dirt or dust attach to the treated surface. There is also no disturbing lubricant sludge. Hygienic, clean and environmentally friendly. The PTFE particles in the submicron range attach even on supposedly very smooth surfaces and give the material an effective glide activity. Successfully tested and tested for all glide layers and for drastically reducing static and roller friction. Typical applications: To drastically reduce static, sliding and rolling friction in rollers and bearings, slides and guide rails, cable tractors and telescopic conductors, gears and gears. Application: shake well before use. Spray on the parts or smooth to be lubricated or surfaced at a distance of 10-25 cm and allow to dry for several minutes Is your PTFE layer sufficient? The static friction of PTFE is just as large as the sliding friction, so the transition from standstill to movement is shock-free. Teflon ™ is a trademark of The Chemours Company FC, LLC used under license by F.W. Klever GmbH
Details
Not in stock - on order
Ballistol universal oil 500ml

€16,95
Whether for handicrafts, home or hobby, for care, protection, cleaning or lubrication, at home, at work or on the go - Ballistol Universal Oil is the right oil for 1,000 cases and more. It is used as a rust protection, lubricating oil, care and cleaning agent and has excelled for more than 115 years with many excellent properties. BALLISTOL UNIVERSAL OIL:

extremely creeping,

sliding actively,

does not wax,

fully biodegradable,

food safe,

skin-friendly,

completely harmless,

environmentally friendly

has a disinfecting effect.

Ballistol Universal Oil was developed in 1904 and has been produced in Germany since then according to an unchanged recipe. All active ingredients in Ballistol Universal Oil are particularly pure, of organic origin and completely degradable. The base oil for Ballistol Universal Oil is medicinally pure, free of chlorinated hydrocarbons and contains no substances of animal origin. In addition, Ballistol Universal Oil is silicone, PTFE, acid and resin-free and harmless within the meaning of Articles 30, 31 of the Food, Consumer Goods and Feed Act (LFGB) and Regulation (EC) No 1935/2004. Ballistol Universal Oil is therefore suitable for the care and maintenance of machines and appliances used in the food and beverage industry that may come into contact with the product. Ballistol Universal Oil cleans, maintains, protects, preserves and dissolves rust and residues such as resins of unsuitable oils and is applicable to wood, leather, stainless steel, iron, non-ferrous metals and oil-resistant rubber. As a universal oil, it can be used in an incredibly versatile way - in professional and hobby workshops, for industry and trade, cars and motorcycles, household and garden, for fishing, sports and for leather and weapon care. There are thousands of practical applications for Ballistol Universal Oil and new ones are always discovered. You can also take advantage of the advantages of the original Ballistol universal oil. Attributes

Material compatibility: rubber (oil resistant), wood, leather, metal/iron

Cleaning: Removing unsuitable fats, removing unsuitable oils, removing gum-like oils/resin, descaling/cleaning connections/contact agents on poles, plug connections, tombac/copper, unwanted patina on copper, brass, stainless steel and aluminum is removed, infiltrated, dissolves rust

Protect: preserved, corrosion protection / rust protection, neutralizes light acids such as hand perspiration

Lubrication: creep oil, lubricating oil, cutting oil / drilling oil
Details
ULTRAIR Power Propellent 570 ml

€9,95

The ULTRAIR Power Gas from ActionSportGames A/S offers high performance within a wide temperature range. The filling valves are specially designed and manufactured in aluminum, creating a strong filling valve that does not break or kink when used. The filling valve leaks very rarely when filling Airsoft pistols, this ensures a very low waste of gas. All ULTRAIR cans are correctly marked according to EU standards. Content: 570ml.

Add to cart Details
Fluna Tec gun coating aerosol 100ml

€13,90
HIGH PERFORMANCE CERAMIC COATING Fluna GunCoating is a high-quality ceramic coating for all types of firearms and knives. Despite its extremely lubricating properties, Fluna GunCoating is residue-free, forms an invisible, dry film on the weapon, and increases the sliding properties of moving parts on the weapon. Loud, metallic sounds of rubbing parts — such as latches on latches on bolt guns — are significantly reduced. Fluna GunCoating forms a firm adhesion with the surface, does not run off and thus protects the weapon against corrosion for a long time. Fluna GunCoating can be applied to all surfaces such as steel, plastic, painted wooden parts, gold and silver decorations, colored pavement, cast iron and rubber. Fluna GunCoating evens out microscopic cracks and grooves and permanently smoothes the treated surfaces. Wear and tear is kept to a minimum and the shooting performance of the weapon is increased. Fluna GunCoating works from the first treatment - even with older pistols! Attributes

Suitable for knives and all types of firearms

Can be applied to any surface

Transparent, residue-free, non-greasy coating

Very good sliding properties, long-lasting effect

Salt and freshwater resistant, economical in use

High temperature resistance from -40°C to +750°C

Does not shear, does not stick, is colorless and odorless

Cleaning the weapon is made easier

MANUAL Fluna GunCoating is always applied to the cleaned weapon. Metal parts must be degreased before use so that the ceramic particles can adhere directly to the metal. Use Fluna Gun Degreaser for degreasing. Fluna GunCoating is sprayed thinly on the surface and then spread out with a lint-free cloth so that a thin, moist film is deposited on the surface. Fluna GunCoating then dries automatically. The coating is dry after approx. 30 minutes at room temperature and fully cured after approx. 2 hours. When using the vessel, make sure that the vessel is thoroughly cleaned beforehand. Fluna GunCoating is then applied thinly with cotton wool or a felt plug. The spray can is recommended for care of large surfaces. The liquid product in the dropper bottle should be used for coating small parts and adjusting the deductions.
Add to cart Details
Fluna Tec gun coating liquid 100ml

€13,90
HIGH PERFORMANCE CERAMIC COATING Fluna GunCoating is a high-quality ceramic coating for all types of firearms and knives. Despite its extremely lubricating properties, Fluna GunCoating is residue-free, forms an invisible, dry film on the weapon, and increases the sliding properties of moving parts on the weapon. Loud, metallic sounds of rubbing parts — such as latches on latches on bolt guns — are significantly reduced. Fluna GunCoating forms a firm adhesion with the surface, does not run off and thus protects the weapon against corrosion for a long time. Fluna GunCoating can be applied to all surfaces such as steel, plastic, painted wooden parts, gold and silver decorations, colored pavement, cast iron and rubber. Fluna GunCoating evens out microscopic cracks and grooves and permanently smoothes the treated surfaces. Wear and tear is kept to a minimum and the shooting performance of the weapon is increased. Fluna GunCoating works from the first treatment - even with older pistols! Attributes

Suitable for knives and all types of firearms

Can be applied to any surface

Transparent, residue-free, non-greasy coating

Very good sliding properties, long-lasting effect

Salt and freshwater resistant, economical in use

High temperature resistance from -40°C to +750°C

Does not shear, does not stick, is colorless and odorless

Cleaning the weapon is made easier

INSTRUCTIONS Fluna GunCoating is always applied to the cleaned weapon. Metal parts must be degreased before use so that the ceramic particles can adhere directly to the metal. Use Fluna Gun Degreaser for degreasing. Fluna GunCoating is thinly dripped on the surface and then spread out with a lint-free cloth so that a thin, moist film is deposited on the surface. Fluna GunCoating then dries automatically. The coating is dry after approx. 30 minutes at room temperature and fully cured after approx. 2 hours. When using the vessel, make sure that the vessel is thoroughly cleaned beforehand. Fluna GunCoating is then applied thinly with cotton wool or a felt plug. The spray can is recommended for care of large surfaces. The liquid product in the dropper bottle should be used for coating small parts and adjusting the deductions.
Add to cart Details
Fluna Tec gun coating aerosol 300ml

€22,90
HIGH PERFORMANCE CERAMIC COATING Fluna GunCoating is a high-quality ceramic coating for all types of firearms and knives. Despite its extremely lubricating properties, Fluna GunCoating is residue-free, forms an invisible, dry film on the weapon, and increases the sliding properties of moving parts on the weapon. Loud, metallic sounds of rubbing parts — such as latches on latches on bolt guns — are significantly reduced. Fluna GunCoating forms a firm adhesion with the surface, does not run off and thus protects the weapon against corrosion for a long time. Fluna GunCoating can be applied to all surfaces such as steel, plastic, painted wooden parts, gold and silver decorations, colored pavement, cast iron and rubber. Fluna GunCoating evens out microscopic cracks and grooves and permanently smoothes the treated surfaces. Wear and tear is kept to a minimum and the shooting performance of the weapon is increased. Fluna GunCoating works from the first treatment - even with older pistols! Attributes

Suitable for knives and all types of firearms

Can be applied to any surface

Transparent, residue-free, non-greasy coating

Very good sliding properties, long-lasting effect

Salt and freshwater resistant, economical in use

High temperature resistance from -40°C to +750°C

Does not shear, does not stick, is colorless and odorless

Cleaning the weapon is made easier

MANUAL Fluna GunCoating is always applied to the cleaned weapon. Metal parts must be degreased before use so that the ceramic particles can adhere directly to the metal. Use Fluna Gun Degreaser for degreasing. Fluna GunCoating is sprayed thinly on the surface and then spread out with a lint-free cloth so that a thin, moist film is deposited on the surface. Fluna GunCoating then dries automatically. The coating is dry after approx. 30 minutes at room temperature and fully cured after approx. 2 hours. When using the vessel, make sure that the vessel is thoroughly cleaned beforehand. Fluna GunCoating is then applied thinly with cotton wool or a felt plug. The spray can is recommended for care of large surfaces. The liquid product in the dropper bottle should be used for coating small parts and adjusting the deductions.
Add to cart Details
Fluna Tec Gun Cleaner

€22,90
Fluna Gun Cleaner is a high-performance running cleaning paste. It removes gunpowder and metal such as lead, copper or Tombak from the barrel and can be used for smooth and drawn barrels of pistols or long weapons. Scopes For the fast, mechanical cleaning of drawn and smooth running of rifles, pistols and revolvers. Do not apply to polished or otherwise treated metal surfaces, on plastic or wood. Attributes

Easy to use

Cleans very effectively

Fast results

Safe for the drum steel

APPLICATIONS Dip a clean felt plug in Fluna GunDegreaser or conventional degreaser and run it through the barrel to remove the coarse dirt. This can also be "dry" with a Bore-Snake. Then turn a plastic brush into Fluna GunCleaner and apply Fluna Gun Cleaner evenly several times in the barrel. Instead of the plastic brush, felt plugs or patches can also be used. The pasta works for about ten minutes, but don't let it dry! Then, with a bronze brush, mechanically remove the metal smear from the room in several movements. Use cleaning rod guide! After cleaning, remove the mixture of paste and metal grease from the barrel with Fluna GunDegreaser. Wipe the barrel until the white felt plugs come out of the barrel. Finally, treat the barrel with Fluna GunCoating. Store the can in a cool, dry place.
Add to cart Details
Fluna Tec gun coating liquid 50ml

€10,90
HIGH PERFORMANCE CERAMIC COATING Fluna GunCoating is a high-quality ceramic coating for all types of firearms and knives. Despite its extremely lubricating properties, Fluna GunCoating is residue-free, forms an invisible, dry film on the weapon, and increases the sliding properties of moving parts on the weapon. Loud, metallic sounds of rubbing parts — such as latches on latches on bolt guns — are significantly reduced. Fluna GunCoating forms a firm adhesion with the surface, does not run off and thus protects the weapon against corrosion for a long time. Fluna GunCoating can be applied to all surfaces such as steel, plastic, painted wooden parts, gold and silver decorations, colored pavement, cast iron and rubber. Fluna GunCoating evens out microscopic cracks and grooves and permanently smoothes the treated surfaces. Wear and tear is kept to a minimum and the shooting performance of the weapon is increased. Fluna GunCoating works from the first treatment - even with older pistols! Attributes

Suitable for knives and all types of firearms

Can be applied to any surface

Transparent, residue-free, non-greasy coating

Very good sliding properties, long-lasting effect

Salt and freshwater resistant, economical in use

High temperature resistance from -40°C to +750°C

Does not shear, does not stick, is colorless and odorless

Cleaning the weapon is made easier

INSTRUCTIONS Fluna GunCoating is always applied to the cleaned weapon. Metal parts must be degreased before use so that the ceramic particles can adhere directly to the metal. Use Fluna Gun Degreaser for degreasing. Fluna GunCoating is thinly dripped on the surface and then spread out with a lint-free cloth so that a thin, moist film is deposited on the surface. Fluna GunCoating then dries automatically. The coating is dry after approx. 30 minutes at room temperature and fully cured after approx. 2 hours. When using the vessel, make sure that the vessel is thoroughly cleaned beforehand. Fluna GunCoating is then applied thinly with cotton wool or a felt plug. The spray can is recommended for care of large surfaces. The liquid product in the dropper bottle should be used for coating small parts and adjusting the deductions.
Add to cart Details
Fluna Tec Gun Degreaser

€9,90
SPECIAL DEGREASER & CLEANER Fluna GunDegreaser is a special cleaner and degreaser for removing oils, fats, waxes, but also pillows and other combustion residues. Fluna GunDegreaser can be used manually or in an ultrasonic bath. Attributes

Cleans without residue and degreases at the same time

Easy to use, does not affect rubber and plastics

APPLICATIONS Degrease Drip Fluna GunDegreaser on the designated area, divide it with a dry cloth and wipe it. Existing oils and fats are removed immediately and without residues. Repeat the process several times if necessary. Cleaning of walking Before Fluna GunCleaner or Fluna Bore Pro (drum cleaning products) is applied, the barrel must already be free of powder smoke and moist. To do this, use Fluna GunDegreaser. Put this on a clean felt plug and push it through the dirty vessel out of the room. After using Fluna GunCleaner or Fluna Bore Pro and scraping the metal smear with a bronze or copper brush, the barrel should be wiped out of the cartridge chamber with Fluna GunDegreaser until no more dirt can be seen on the felt plug. The barrel is then degreased at the same time and can be re-coated with Fluna GunCoating. Cleaning of rifle and pistol parts Drip Fluna GunDegreaser on the dirty surface and let it soak in for a while. Then, if necessary, loosen the dirt with a brush and wipe it with a cloth. After cleaning, the surface is also degreased and prepared for coating with Fluna GunCoating. Fluna GunDegreaser does not affect paint, rubber or molded parts. Fluna Gun Degreaser is also excellent at removing black powder residues
Add to cart Details
Fluna Tec TFT optic cleaner 100ml

€13,90
AEROSOL FOAM CLEANER Fluna TFT/optics foam cleaner is a special foam for cleaning all kinds of optics, binoculars, rifle scopes, spotting scopes. Fluna TFT/Optical Foam Cleaner also cleans flat screens such as TFT - LCD monitors, laptop screens, televisions, PDAs, navigation devices, glass and mirrors. Fluna TFT/optical foam cleaner can also be used on plastic and rubber surfaces. Fluna TFT/Optical Foam Cleaner removes all household dirt such as dust, nicotine, insects, grease stains, fingerprints, patina from hand sweat and dust. Attributes

Extremely high stability

High cleaning power

Does not penetrate the housing

Cleans without leaving residue

Contains no alcohol

Simple application

APPLICATION Hunting optics, e.g. rifle scope Before cleaning, blow off the optics with compressed air or remove the coarse dust. Spray Fluna TFT/optics foam cleaner from the front against the glass so that the expanding foam completely fills the space between the glass and the end of the rifle scope. After a short exposure time, walk along the grooved day side with a dry, clean cloth and thus remove the hanging dust from the sun visor. In a second step, spray the cleaner thinly on the glass and clean and polish it with a dry, clean cloth. Fencing Apply Fluna TFT / Optic Foam Cleaner evenly and thinly on the surfaces and leave on for a few seconds, dirt to loosen. Spread the product with a soft cloth and remove dirt. We recommend turning off the device during use. When cleaning plastics, we recommend a longer working time of the product.
Add to cart Details
Fluna Tec Gun Black

€13,90
FAST BLUES - COLD BLUES Fluna Gun Black is a quick tan (cold browning) for repairing tanning on rifle and pistol barrels. It is also suitable for blackening small metal parts such as screw heads etc. Attributes

Easy to use

Good degree of blacking

Fast results

Application First clean the damaged area thoroughly and degrease it with Fluna GunDegreaser, a degreaser or with alcohol. The damaged area can also be sanded again with sandpaper grain 1000 or with a scouring sponge. Use strong adhesive tape to clearly delineate the repair. Apply Fluna GunBlack thinly with a fine brush or cotton swab and let it dry. Repeat the process several times until the desired degree of blackening is reached. Then neutralize the repair with gun coating, drying and polishing. Finally, treat the repaired area again with Fluna GunCoating. Fluna Gun Black can in principle also be applied to a cloth for larger areas and the area to be treated can then be colored with the cloth by repeatedly sweeping it back and forth.
Add to cart Details