Fluna Tec Archieven

Not in stock - on order
Fluna Tec Anti-Fog optics care set

€39,90
THE FLUNA TEC OPTIC CARE SET For anyone who wants to clean and care optimally for hunting and sports optics. With this set, you get all the products you need for professional cleaning of the optics, including anticondens for all lenses. The set contains the following individual products:

Fluna TFT / optic cleaner 100ml (RETFT00701)

Fluna isopropanol 50ml (RIS0050120)

Fluna Anti Fog 50ml (ABG0050120)

Microfibre cloth 40 / 40cm

Glass polish 20/20 each packed

On the back of the inlet is a detailed product description.

The product description of the individual products in the set can be found in the relevant item.

Instructions:

First, remove loose dust from the optics – preferably by "blowing out" with a jet of compressed air.

Clean the optics with the Fluna TFT/optic foam cleaner. Turn off electrical appliances for cleaning. Apply foam cleaner evenly thin (leave briefly inactive in case of strong pollution). Dry brush with the clean microfibre cloth.

After cleaning, spray the glass of the optics with the isopropanol alcohol, to defropher the surface. Divide the alcohol with the included glass cloth and wipe away the excess liquid. Let the surface dry for a few seconds.

Then spray the product Fluna spray against covering evenly thin on the glass surface and let the flow substance in for about 2 minutes. Then take the glass polish cloth and brush the glass surface evenly for as long until there is no more liquid to be seen and the glass surface is evenly covered and streakless. Allow the coating to dry for at least 30 minutes. To you can breathe against the glass. If the coating is applied correctly, the mist should dissolve immediately.
Details
Fluna Tec bore pro 100ml

€13,90
Use Fluna Gun Degreaser to clean the vessel from coarse dirt such as powder smoke, etc. Bring Fluna BORE PRO into the vessel, e.g. with a soaked felt pad or with a wet metal brush. Use a brushing stick guide. Make sure that the running steel is completely and evenly moistened. After the exposure time of approx. 15 minutes. moisten a metal brush (copper or brass) again with Fluna BORE PRO and push it in the barrel towards the bulkhead. Pay attention to caliber-precise brushes! With about 10 back and forth movements you brush away the metal deposits. Finally, wipe the barrel several times with clean felt pads or plasters and remove the deposit from the barrel. At the same time, the barrel is preserved by the remaining amount of Fluna BORE PRO, neutralization is not necessary. Alternatively, you can completely wipe the Fluna BORE PRO out of the barrel with Fluna Gun Degreaser and then preserve it as usual with Fluna Gun Coating. Attributes

Cleans and preserves

Very effective and fast results

Harmless to running steel

Scopes For fast, dry cleaning of drawn and smooth barrels of rifles, pistols and revolvers. Do not apply to polished or otherwise treated metal surfaces, plastic or wood.
Add to cart Details
Fluna Tec Gun Black

€13,90
FAST BLUES - COLD BLUES Fluna Gun Black is a quick tan (cold browning) for repairing tanning on rifle and pistol barrels. It is also suitable for blackening small metal parts such as screw heads etc. Attributes

Easy to use

Good degree of blacking

Fast results

Application First clean the damaged area thoroughly and degrease it with Fluna GunDegreaser, a degreaser or with alcohol. The damaged area can also be sanded again with sandpaper grain 1000 or with a scouring sponge. Use strong adhesive tape to clearly delineate the repair. Apply Fluna GunBlack thinly with a fine brush or cotton swab and let it dry. Repeat the process several times until the desired degree of blackening is reached. Then neutralize the repair with gun coating, drying and polishing. Finally, treat the repaired area again with Fluna GunCoating. Fluna Gun Black can in principle also be applied to a cloth for larger areas and the area to be treated can then be colored with the cloth by repeatedly sweeping it back and forth.
Add to cart Details
Fluna Tec Gun Care care set 2

€39,95
With the Fluna Gun Care Set 1, cleaning weapons has never been easier. With three Fluna Tec main products and matching microfiber cloth, you can clean your entire weapon without oil. From now on, you can rely on clean, economical and odorless gun cleaning and maintenance with ceramic coating. Cleaning firearms is usually not the most popular activity, but it is an extremely necessary one to ensure the desired features and smooth operation of firearms. The good news is that the products in Fluna Gun Care Set 1 are enough to completely clean and maintain your technically advanced firearms - without oil! - to clean and maintain them completely. Discover the time-saving and effective Fluna Tec system: clean all parts of the weapon, free the barrel from metal contamination and protect your weapon with the high-quality ceramic coating that professionals rely on. CONTENTS OF FLUNA GUN CARE SET 2

Fluna Gun Coating Aerosol 100 ml

Fluna Gun Degreaser 100 ml

Fluna Gun Cleaner 50 g

Microfibre cloth 40×40 cm

1 / FLUNA GUN COATING AEROSOL Rely on the perfect care of your gun with the high-quality ceramic coating from Fluna Tec in the practical spray bottle. The transparent, residue-free and non-greasy coating can be applied to any surface. It convinces with high temperature resistance, the best corrosion protection and a long-lasting effect. 2 / FLUNA GUN DEGREASER With this special gun cleaner and degreaser in a bottle, you can remove oils, greases, waxes, gunpowder smoke, and other combustion residues. You can use the gun cleaner manually and in an ultrasonic bath. 3 / FLUNA GUN CLEANER Heavy duty barrel cleaning paste in a can is the perfect choice for smooth and serrated barrels of rifles, pistols and revolvers. Quickly and completely removes gunpowder residue, lead, copper and tombac from all types of barrels. 4 / LINT-FREE MICROFIBER CLOTH For a streak-free, thorough and residue-free cleaning of your gun, we recommend the microfiber cloth included in Gun Care Set 2. Wash your used cloth at 60°C in the washing machine without fabric softener. FLUNA TEC GUN CLEANING FOR SPORT AND HUNTING Professional teams have long relied on Fluna Tec's oil-free, economical and highly effective firearms cleaning and maintenance products. Produced to the highest standards and in constant compliance with the requirements of professionals and amateurs, Fluna Tec takes the care of valuable firearms, knives and optics to a new level.
Add to cart Details
Fluna Tec Gun care set 1

€29,90

PISTOL MAINTENANCE FOR BEGINNERS AND SWITCHERS With the Fluna Gun Care Set 2 you can say goodbye to conventional gun oil with all the known drawbacks. From now on, you too can benefit from modern and effective pistol cleaning and Gun Care with a resistant, high-quality ceramic coating for your technically demanding weapons. Do it the same way professional teams do: use weapon maintenance that is economical, easy to use, odor-free, and with a long-lasting effect. With just two products from the Fluna Tec family of maintenance products, you can clean and maintain your firearms and knives in just a few steps. Get to know Fluna Tec weapon maintenance with the practical starter set, experience it for yourself and use other products as desired in the future, making the tedious weapon maintenance a time-saving pleasure. CONTENTS OF FLUNA GUN CARE SET 1 Fluna Gun Coating Aerosol 100 ml Fluna Gun Degreaser 100 ml Microfibre cloth 30 x 30 cm 1 / FLUNA GUN COATING AEROSOL In the future, use Fluna Tec's high-quality ceramic coating for weapon maintenance. Firearms and knives are protected by the sparsely applied film; Moving parts permanently run as if lubricated - dry and without the disadvantages of conventional gun oil. 2 / FLUNA GUN DEGREASER Cleaning guns is so easy: with the special cleaner and degreaser, oils and greases, waxes, as well as gunpowder smoke and combustion residues are quickly and completely removed. Fluna Gun Degreaser in the practical bottle is suitable for cleaning by hand and in an ultrasonic bath. 3 / LINT-FREE MICROFIBER CLOTH Use the microfiber cloth from the kit to clean all parts of your gun and get a streak-free, shiny result. After use, simply wash the microfibre cloth in the washing machine at 60 °C without fabric softener. INTRODUCING FLUNA TEC GUN MAINTENANCE By choosing Fluna gun care set 2, you have taken the first step towards an oil-free future for your gun. You are in the best company, because professional athletes, hunters and special forces in many countries have already opted for Fluna Tec's economical, clean and effective weapon maintenance.

Add to cart Details
Fluna Tec Gun Cleaner

€22,90
Fluna Gun Cleaner is a high-performance running cleaning paste. It removes gunpowder and metal such as lead, copper or Tombak from the barrel and can be used for smooth and drawn barrels of pistols or long weapons. Scopes For the fast, mechanical cleaning of drawn and smooth running of rifles, pistols and revolvers. Do not apply to polished or otherwise treated metal surfaces, on plastic or wood. Attributes

Easy to use

Cleans very effectively

Fast results

Safe for the drum steel

APPLICATIONS Dip a clean felt plug in Fluna GunDegreaser or conventional degreaser and run it through the barrel to remove the coarse dirt. This can also be "dry" with a Bore-Snake. Then turn a plastic brush into Fluna GunCleaner and apply Fluna Gun Cleaner evenly several times in the barrel. Instead of the plastic brush, felt plugs or patches can also be used. The pasta works for about ten minutes, but don't let it dry! Then, with a bronze brush, mechanically remove the metal smear from the room in several movements. Use cleaning rod guide! After cleaning, remove the mixture of paste and metal grease from the barrel with Fluna GunDegreaser. Wipe the barrel until the white felt plugs come out of the barrel. Finally, treat the barrel with Fluna GunCoating. Store the can in a cool, dry place.
Add to cart Details
Fluna Tec gun coating aerosol 100ml

€13,90
HIGH PERFORMANCE CERAMIC COATING Fluna GunCoating is a high-quality ceramic coating for all types of firearms and knives. Despite its extremely lubricating properties, Fluna GunCoating is residue-free, forms an invisible, dry film on the weapon, and increases the sliding properties of moving parts on the weapon. Loud, metallic sounds of rubbing parts — such as latches on latches on bolt guns — are significantly reduced. Fluna GunCoating forms a firm adhesion with the surface, does not run off and thus protects the weapon against corrosion for a long time. Fluna GunCoating can be applied to all surfaces such as steel, plastic, painted wooden parts, gold and silver decorations, colored pavement, cast iron and rubber. Fluna GunCoating evens out microscopic cracks and grooves and permanently smoothes the treated surfaces. Wear and tear is kept to a minimum and the shooting performance of the weapon is increased. Fluna GunCoating works from the first treatment - even with older pistols! Attributes

Suitable for knives and all types of firearms

Can be applied to any surface

Transparent, residue-free, non-greasy coating

Very good sliding properties, long-lasting effect

Salt and freshwater resistant, economical in use

High temperature resistance from -40°C to +750°C

Does not shear, does not stick, is colorless and odorless

Cleaning the weapon is made easier

MANUAL Fluna GunCoating is always applied to the cleaned weapon. Metal parts must be degreased before use so that the ceramic particles can adhere directly to the metal. Use Fluna Gun Degreaser for degreasing. Fluna GunCoating is sprayed thinly on the surface and then spread out with a lint-free cloth so that a thin, moist film is deposited on the surface. Fluna GunCoating then dries automatically. The coating is dry after approx. 30 minutes at room temperature and fully cured after approx. 2 hours. When using the vessel, make sure that the vessel is thoroughly cleaned beforehand. Fluna GunCoating is then applied thinly with cotton wool or a felt plug. The spray can is recommended for care of large surfaces. The liquid product in the dropper bottle should be used for coating small parts and adjusting the deductions.
Add to cart Details
Fluna Tec gun coating aerosol 300ml

€22,90
HIGH PERFORMANCE CERAMIC COATING Fluna GunCoating is a high-quality ceramic coating for all types of firearms and knives. Despite its extremely lubricating properties, Fluna GunCoating is residue-free, forms an invisible, dry film on the weapon, and increases the sliding properties of moving parts on the weapon. Loud, metallic sounds of rubbing parts — such as latches on latches on bolt guns — are significantly reduced. Fluna GunCoating forms a firm adhesion with the surface, does not run off and thus protects the weapon against corrosion for a long time. Fluna GunCoating can be applied to all surfaces such as steel, plastic, painted wooden parts, gold and silver decorations, colored pavement, cast iron and rubber. Fluna GunCoating evens out microscopic cracks and grooves and permanently smoothes the treated surfaces. Wear and tear is kept to a minimum and the shooting performance of the weapon is increased. Fluna GunCoating works from the first treatment - even with older pistols! Attributes

Suitable for knives and all types of firearms

Can be applied to any surface

Transparent, residue-free, non-greasy coating

Very good sliding properties, long-lasting effect

Salt and freshwater resistant, economical in use

High temperature resistance from -40°C to +750°C

Does not shear, does not stick, is colorless and odorless

Cleaning the weapon is made easier

MANUAL Fluna GunCoating is always applied to the cleaned weapon. Metal parts must be degreased before use so that the ceramic particles can adhere directly to the metal. Use Fluna Gun Degreaser for degreasing. Fluna GunCoating is sprayed thinly on the surface and then spread out with a lint-free cloth so that a thin, moist film is deposited on the surface. Fluna GunCoating then dries automatically. The coating is dry after approx. 30 minutes at room temperature and fully cured after approx. 2 hours. When using the vessel, make sure that the vessel is thoroughly cleaned beforehand. Fluna GunCoating is then applied thinly with cotton wool or a felt plug. The spray can is recommended for care of large surfaces. The liquid product in the dropper bottle should be used for coating small parts and adjusting the deductions.
Add to cart Details
Fluna Tec gun coating liquid 100ml

€13,90
HIGH PERFORMANCE CERAMIC COATING Fluna GunCoating is a high-quality ceramic coating for all types of firearms and knives. Despite its extremely lubricating properties, Fluna GunCoating is residue-free, forms an invisible, dry film on the weapon, and increases the sliding properties of moving parts on the weapon. Loud, metallic sounds of rubbing parts — such as latches on latches on bolt guns — are significantly reduced. Fluna GunCoating forms a firm adhesion with the surface, does not run off and thus protects the weapon against corrosion for a long time. Fluna GunCoating can be applied to all surfaces such as steel, plastic, painted wooden parts, gold and silver decorations, colored pavement, cast iron and rubber. Fluna GunCoating evens out microscopic cracks and grooves and permanently smoothes the treated surfaces. Wear and tear is kept to a minimum and the shooting performance of the weapon is increased. Fluna GunCoating works from the first treatment - even with older pistols! Attributes

Suitable for knives and all types of firearms

Can be applied to any surface

Transparent, residue-free, non-greasy coating

Very good sliding properties, long-lasting effect

Salt and freshwater resistant, economical in use

High temperature resistance from -40°C to +750°C

Does not shear, does not stick, is colorless and odorless

Cleaning the weapon is made easier

INSTRUCTIONS Fluna GunCoating is always applied to the cleaned weapon. Metal parts must be degreased before use so that the ceramic particles can adhere directly to the metal. Use Fluna Gun Degreaser for degreasing. Fluna GunCoating is thinly dripped on the surface and then spread out with a lint-free cloth so that a thin, moist film is deposited on the surface. Fluna GunCoating then dries automatically. The coating is dry after approx. 30 minutes at room temperature and fully cured after approx. 2 hours. When using the vessel, make sure that the vessel is thoroughly cleaned beforehand. Fluna GunCoating is then applied thinly with cotton wool or a felt plug. The spray can is recommended for care of large surfaces. The liquid product in the dropper bottle should be used for coating small parts and adjusting the deductions.
Add to cart Details
Fluna Tec gun coating liquid 50ml

€10,90
HIGH PERFORMANCE CERAMIC COATING Fluna GunCoating is a high-quality ceramic coating for all types of firearms and knives. Despite its extremely lubricating properties, Fluna GunCoating is residue-free, forms an invisible, dry film on the weapon, and increases the sliding properties of moving parts on the weapon. Loud, metallic sounds of rubbing parts — such as latches on latches on bolt guns — are significantly reduced. Fluna GunCoating forms a firm adhesion with the surface, does not run off and thus protects the weapon against corrosion for a long time. Fluna GunCoating can be applied to all surfaces such as steel, plastic, painted wooden parts, gold and silver decorations, colored pavement, cast iron and rubber. Fluna GunCoating evens out microscopic cracks and grooves and permanently smoothes the treated surfaces. Wear and tear is kept to a minimum and the shooting performance of the weapon is increased. Fluna GunCoating works from the first treatment - even with older pistols! Attributes

Suitable for knives and all types of firearms

Can be applied to any surface

Transparent, residue-free, non-greasy coating

Very good sliding properties, long-lasting effect

Salt and freshwater resistant, economical in use

High temperature resistance from -40°C to +750°C

Does not shear, does not stick, is colorless and odorless

Cleaning the weapon is made easier

INSTRUCTIONS Fluna GunCoating is always applied to the cleaned weapon. Metal parts must be degreased before use so that the ceramic particles can adhere directly to the metal. Use Fluna Gun Degreaser for degreasing. Fluna GunCoating is thinly dripped on the surface and then spread out with a lint-free cloth so that a thin, moist film is deposited on the surface. Fluna GunCoating then dries automatically. The coating is dry after approx. 30 minutes at room temperature and fully cured after approx. 2 hours. When using the vessel, make sure that the vessel is thoroughly cleaned beforehand. Fluna GunCoating is then applied thinly with cotton wool or a felt plug. The spray can is recommended for care of large surfaces. The liquid product in the dropper bottle should be used for coating small parts and adjusting the deductions.
Add to cart Details
Fluna Tec Gun Degreaser

€9,90
SPECIAL DEGREASER & CLEANER Fluna GunDegreaser is a special cleaner and degreaser for removing oils, fats, waxes, but also pillows and other combustion residues. Fluna GunDegreaser can be used manually or in an ultrasonic bath. Attributes

Cleans without residue and degreases at the same time

Easy to use, does not affect rubber and plastics

APPLICATIONS Degrease Drip Fluna GunDegreaser on the designated area, divide it with a dry cloth and wipe it. Existing oils and fats are removed immediately and without residues. Repeat the process several times if necessary. Cleaning of walking Before Fluna GunCleaner or Fluna Bore Pro (drum cleaning products) is applied, the barrel must already be free of powder smoke and moist. To do this, use Fluna GunDegreaser. Put this on a clean felt plug and push it through the dirty vessel out of the room. After using Fluna GunCleaner or Fluna Bore Pro and scraping the metal smear with a bronze or copper brush, the barrel should be wiped out of the cartridge chamber with Fluna GunDegreaser until no more dirt can be seen on the felt plug. The barrel is then degreased at the same time and can be re-coated with Fluna GunCoating. Cleaning of rifle and pistol parts Drip Fluna GunDegreaser on the dirty surface and let it soak in for a while. Then, if necessary, loosen the dirt with a brush and wipe it with a cloth. After cleaning, the surface is also degreased and prepared for coating with Fluna GunCoating. Fluna GunDegreaser does not affect paint, rubber or molded parts. Fluna Gun Degreaser is also excellent at removing black powder residues
Add to cart Details
Fluna Tec Gun Oil Aerosol 200ml

€11,90

With Fluna Gun Oil we have developed a pistol oil that, as a CLP product, is a cost-effective alternative to the premium product Fluna Gun Coating. Fluna Gun Oil is a weapon oil of the latest generation and cleans, lubricates and maintains metal parts. Fluna Gun Oil is free of heavy metals and free of PCB, PCT and phenol. USE OF THE FLUNA PISTOL OIL Fluna Gun Oil should always be applied to the cleaned surface. It is not necessary to degrease the surface before application. For external application on pistols, the aerosol product is more suitable due to the spray pattern. For precise application, e.g. on sliding guides, use the liquid product with the practical dropper. Pistol oil is applied to the surfaces to be treated. PISTOL CLEANING WITH FLUNA TEC The constant and careful cleaning and care of all parts of the weapon guarantees the greatest pleasure and success in both the sport and the hunt. Fluna Tec offers a special product for every application. The Fluna Tec product family has been developed from practice and is used worldwide by professionals and ambitious amateurs.

Add to cart Details
Fluna Tec Optics Care Set No.5

€39,45

BEST OPTICS CARE FOR HUNTING AND SPORTS The Fluna optical care set contains three coordinated products for residue-free cleaning, long-lasting protection and effective anti-fog coating. Prepare your high-quality optics optimally for sport and hunting and benefit from crystal-clear visibility in all temperatures and weather conditions. A clear, unobstructed view is an essential prerequisite for achieving the desired results in sports and hunting. Nothing is more annoying than a lens with streaks or fogged up that makes precise aiming practically impossible. With the Fluna optics maintenance set, you can ensure that your optics optimally support your ambitions at all times and under all conceivable external circumstances in just three simple and quick steps. 1 / FLUNA TFT OPTICS CLEANER With this special foam, which comes in a handy spray can, you can clean all types of optics, binoculars, riflescopes and spotting scopes. You can also clean flat screens such as navigation systems or hunting and sports cameras in no time. The alcohol-free optics cleaner does not penetrate the housing and is easy to use with a clean, dry cloth. 2 / FLUNA ISOPROPANOL With this product in the practical pump bottle, you can degrease all glass surfaces that you then want to treat with Fluna Anti-Fog. The anti-fog coating is especially popular in yacht optics, as it is exposed to different temperatures and weather conditions. Simply spray on, leave on for a few minutes and polish with a clean cloth (included in the kit). 3 / FLUNA ANTI-FOG The third product in the Fluna optical care set is an effective and durable solvent-based coating that is suitable for all types of glass - and in particular for hunting optics. With just a few sprays from the bottle onto the optics prepared with Fluna Isopropanol, a short exposure time and then polishing, you can apply an anti-fog coating whose effect lasts from a few days to weeks. 4 / LINT-FREE MICROFIBER CLOTH The microfiber cloth with a size of 40 x 40 centimeters is the best choice for cleaning your optics. Make sure it is always clean and dry during use for optimal results. After use, wash the microfibre cloth in the washing machine at 60 °C without fabric softener. 5 / EYEGLASS CLEANING CLOTH - POLISHING CLOTH To polish the lenses, it is best to use the lens polishing cloth from the Fluna Optik care set. Make sure it's clean and dry when you use it – this is the only way to ensure that the glasses are truly streak-free and one hundred percent clean. You can also use this special lens polishing cloth to polish the anti-fog coating for hunting optics. PISTOL MAINTENANCE WITH THE FLUNA TEC RANGE Cleaning, gun maintenance and the associated optical care should ideally be as simple as possible and require only a minimum of time. With Fluna Tec's cleaning and weapon care products, you choose products that are perfectly matched to each other and easy to use. Do as the pros in sport and hunting do and buy your Fluna optical care kit.

Add to cart Details
Not in stock - on order
Fluna Tec Silencer Cleaning Kit

€25,90
EASY CLEANING SILENCERS AND SUPPRESSORS. As with all parts of a firearm, the silencer also applies: regular cleaning protects against damage and retains the value of the suppressor. After about 50 to a maximum of 200 bullets, you should thoroughly clean and preserve your silencer - ideally with the Fluna Silencer Cleaner Set. The use of a silencer in hunting, as well as in sports, is recommended for several reasons. By dampening the muzzle radius, the hearing of man and dog is protected and the perception of the bullet impact is improved. In addition, the silencer reduces the recoil, which increases the chance of success. The interfering flash in diffuse light is also significantly reduced. By cleaning your silencer, you protect yourself and others and increase your marksmanship. CONTENT WEAPON CARE SET 4

Fluna SDR concentrate 250 ml (for 2 applications)

PVC lid for cleaning in solution

Microfibre cloth 40 x 40 cm

1 / FLUNA SDR DAMPER CLEANER From now on, use Fluna SDR, the special cleaner and degreaser for all silencers, for the automatic cleaning of your suppressor. Fluna SDR automatically cleans metal surfaces from crumb smoke and all combustion residues. Simply put the detergent in the supplied bottle, place the damper disassembled or unassembled and you will achieve the desired result after 30 minutes to two hours without further effort. 2 / LINT-FREE MICROFIBRE CLOTH 40 X 40 CM Clean accessible areas on the silencer after removing it from the Fluna SDR cleaning solution with the included microfiber cloth. After use, it is best to wash the cloth in the washing machine at 60 °C without fabric softener. 3 / BOTTLE FOR DAMPER CLEANING The plastic bottle or lid is used to apply the cleaning solution by placing the silencer in it. After cleaning, wash the silencer thoroughly with water, dry it with a cloth and leave the hood open until it is completely dry. TUTORIAL FLUNA SDR APPLICATION Dilute half of the concentrate in the empty PVC lid with water in a ratio of 1:3 to obtain 500 ml of cleaning solution. If possible, disassemble the silencer and place it in the envelope containing the cleaning mixture. Fluna SDR now automatically cleans your silencer - depending on the degree of contamination within 30 minutes to two hours. Support the cleansing process by shaking gently from time to time. The cleaning solution acquires a more intense black color; this indicates a successful cleaning. Remove the silencer from the solution and clean the accessible areas with the microfibre cloth. Then rinse the Supressor vigorously with running water and loosen any dirt residue by beating and shaking. After drying, you can reassemble your damper. Tip: Check the material compatibility before the first use!
CLEANING AND MAINTENANCE OF WEAPONS WITH FLUNA TEC Fluna Tec's experts are constantly working to make necessary and important weapon care as easy and straightforward as possible, while meeting the highest standards. Professional marksmen, action teams and hunters rely on Fluna Tec products - you too can use the Fluna Tec range to preserve the value of your firearms and knives!
Details
Fluna Tec TFT optic cleaner 100ml

€13,90
AEROSOL FOAM CLEANER Fluna TFT/optics foam cleaner is a special foam for cleaning all kinds of optics, binoculars, rifle scopes, spotting scopes. Fluna TFT/Optical Foam Cleaner also cleans flat screens such as TFT - LCD monitors, laptop screens, televisions, PDAs, navigation devices, glass and mirrors. Fluna TFT/optical foam cleaner can also be used on plastic and rubber surfaces. Fluna TFT/Optical Foam Cleaner removes all household dirt such as dust, nicotine, insects, grease stains, fingerprints, patina from hand sweat and dust. Attributes

Extremely high stability

High cleaning power

Does not penetrate the housing

Cleans without leaving residue

Contains no alcohol

Simple application

APPLICATION Hunting optics, e.g. rifle scope Before cleaning, blow off the optics with compressed air or remove the coarse dust. Spray Fluna TFT/optics foam cleaner from the front against the glass so that the expanding foam completely fills the space between the glass and the end of the rifle scope. After a short exposure time, walk along the grooved day side with a dry, clean cloth and thus remove the hanging dust from the sun visor. In a second step, spray the cleaner thinly on the glass and clean and polish it with a dry, clean cloth. Fencing Apply Fluna TFT / Optic Foam Cleaner evenly and thinly on the surfaces and leave on for a few seconds, dirt to loosen. Spread the product with a soft cloth and remove dirt. We recommend turning off the device during use. When cleaning plastics, we recommend a longer working time of the product.
Add to cart Details

Title